This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Ammonia Plus Hydrogen as Fuel in a S.I. Engine: Experimental Results
Technical Paper
2012-32-0019
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Storing hydrogen is one of the major problems concerning its
utilization on board vehicles. Today hydrogen can be compressed and
stored at 200 or 350 bar (it is foreseen that in a near future
storage pressure will reach 700 bar, according to new expected
regulations and using tanks in composite materials) or
cryogenically liquefied.
An alternative solution is storing hydrogen in the form of
ammonia that is liquid at roughly 9 bar at environmental
temperature and therefore involves relatively small masses and
volumes and requires light and low-cost tanks. Moreover, ammonia
contains almost 18% hydrogen by mass and, by volume, liquid ammonia
contains 1.7 times as much hydrogen as liquid hydrogen.
It is well known that ammonia can be burned directly in I.C.
engines, however a combustion promoter is necessary to support
combustion especially in the case of high-speed S.I. engines. Among
the potential promoters, hydrogen is worthy of note, since it is
carbon free and counteracts ammonia combustion characteristics. As
a matter of fact, hydrogen has high combustion velocity and wide
flammability range, whereas ammonia combustion is characterized by
low flame speed, low flame temperature, narrow flammability range,
high ignition energy and high self-ignition temperature.
The experimental activity shown in this paper is correlated with
a project that is focused on a range-extended electric vehicle
involving an ammonia-plus-hydrogen I.C. engine and where hydrogen
is obtained from ammonia by means of on-board catalytic reforming.
Accordingly, the test engine is a 505 cm₃ Lombardini twin-cylinder
S.I. engine that is well suited to power the onboard electric
generator and the activity is aimed at determining proper
air-ammonia-hydrogen mixture compositions at actual operating
speeds and loads of the engine connected to the electric
generator.
Hydrogen and ammonia are separately injected in the gaseous
phase. The only mechanical modification of the engine involves the
intake manifold, where electro-injectors for hydrogen and for
ammonia (conventional ones for CNG application with appropriate
modification to inner parts) are added to the original ones for
gasoline.
The experimental results confirm that it is necessary to add
hydrogen to air-ammonia mixture to improve ignition and to increase
combustion velocity, with ratios that depend mainly on load and
less on engine speed. Brake power is less than with gasoline, due
to mixture poor volumetric heating value and to ammonia low flame
speed that penalizes engine brake thermal efficiency. The amount of
hydrogen needed by the engine is compatible with the flow rate
provided by the reformer, except at cold start. The maximum
NOx emission is 11.5 g/kWh at half load and 4500 rpm,
without catalytic reduction.
Recommended Content
Authors
Topic
Citation
Frigo, S., Gentili, R., and Doveri, N., "Ammonia Plus Hydrogen as Fuel in a S.I. Engine: Experimental Results," SAE Technical Paper 2012-32-0019, 2012, https://doi.org/10.4271/2012-32-0019.Also In
References
- Cornelius, W. Huellmantel, L. Mitchell, H. “Ammonia as an Engine Fuel,” SAE Technical Paper 650052 1965 10.4271/650052
- Starkman, E. Newhall, H. Sutton, R. Maguire, T. et al. “Ammonia as a Spark Ignition Engine Fuel: Theory and Application,” SAE Technical Paper 660155 1966 10.4271/660155
- Gray, J. Dimitroff, E. Meckel, N. Quillian, R. “Ammonia Fuel - Engine Compatibility and Combustion,” SAE Technical Paper 660156 1966 10.4271/660156
- Pearsall, T. Garabedian, C. “Combustion of Anhydrous Ammonia in Diesel Engines,” SAE Technical Paper 670947 1967 10.4271/670947
- Zavka, M. “Device for Operating Internal Combustion Engines with Mixtures of Ammonia, Hydrogen and Nitrogen prepared from Ammonia” Patent # 2,140,254 Dec. 13 1938
- Arora, N. Gupta, D. C. P. 1970 “Ammonia as S.I. Engine Fuel” Metals and Mineral Review January 1970
- Mørch, C.S. “Performance of ammonia/hydrogen mixtures in SI engines” Master's thesis Department of Mechanical Engineering, Technical University of Denmark July 2007
- Mørch, C.S. Bjerre, A. Gøttrup, M.P. Sorenson, S.C. Schramm, J. “Ammonia/hydrogen mixtures in an SI-engine: Engine performance and analysis of a proposed fuel system” Fuel 90 854 864 Elsevier 2011
- Ciccarelli, G. Jackson, D. Verreault, J. “Flammability limits of NH 3 -H 2 -N 2 -air mixtures at elevated initial temperatures” Combustion and Flame 144 53 63 Elsevier 2006
- Lee, J.H. Kim, J.H. Park, J.H. Kwon, O.C. “Studies on properties of laminar premixed hydrogen-added ammonia/air flames for hydrogen production” International Journal of Hydrogen Energy 35 1054 1064 Elsevier 2010
- Zamfirescu, C. Dincer, I. “Ammonia as a green fuel and hydrogen source for vehicular applications” Fuel Processing Technology 90 729 737 2009
- Heywood, J. B. “Internal Combustion Engine Fundamentals” McGraw-Hill 1988
- Sierens, R. Verhelst, S “Load control strategies for hydrogen fuelled IC engines” World Hydrogen Technologies Convention (WHTC) New Delhi, India 2009
- White, C.M. Steeper, R.R. Lutz, A.E. 2006 “The hydrogen-fueled internal combustion engine: a technical review” International Journal of Hydrogen Energy 31 1291 1305