This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Effect of Inoculation on Turning Machinability of Gray Cast Iron
Technical Paper
2012-01-1823
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Turning is the widely machining process used for brake rotor manufacturing while turning cost is a one factors that many has a huge impact on manufacturing cost for second tier manufacturer so increase tool life is always needed developed in second tier manufacturer. This paper would like to investigate effect of microstructure and graphite morphology of gray cast iron which is the most widely materials use in brake rotor on machinability. The tested material was class FC250. The raw test was made of steel scrap, returned material at the ratio of 60 : 40. Controlled inoculation technique was inoculated in ladle compare with inoculated both in ladle and were in melting stream while pouring in horizontal greensand mould. The microstructure measured by optical microscopy and cutting force investigated by dynamometer. The experimental were observed to achieve the result of minimize cost among raw material, turning process cost, insert cost, and meet the product criteria of friction brake performance.
Recommended Content
Authors
Topic
Citation
Tongtae, C., Dawan, P., and Kumvong, S., "Effect of Inoculation on Turning Machinability of Gray Cast Iron," SAE Technical Paper 2012-01-1823, 2012, https://doi.org/10.4271/2012-01-1823.Also In
References
- Fenghang, REN Fengjun, LI Weiming, LIU Zhanhong, MA Baohong, TIAN “Effect of inoculating addition on machinability of gray cast iron” Journal of rare earths 27 Apr. 2009 294
- Pereira, Adriana Ana Boehs, Lourival Guesser, Wilson Luiz “The influence of sulfur on the machinability of gray cast iron FC25” Journal of Materials Processing Technology 179 2006 165 171
- Akasawa, Tadahisa Fukuda, Ikuo Nakamura, Kenji Tanaka, Takio “Effect of microstructure and hardness on the machinability of medium-carbon chrome-molybdenum steel” Journal of Materials Processing Technology 153-154 2004 48 53
- Prasad, M. V. R. D. Janardhana, G. Ranga Rao, D. Hanumantha “Experimental investigation to study the influence of process parameters in dry machining” ARPN Journal of Engineering and Applied Sciences 4 3 May 2009
- Kamely, M.A. Noordin, M.Y. “The impact of cutting tool materials on cutting force” International Journal of Engineering and Applied Sciences 7 3 2001
- Oraby, S.E. Hayhurst, D.R. “Tool life determination based on the measurement of wear and tool force ratio variation” International journal of machine tools & manufacture 44 2004 1261 1269
- Gastel, M. Konetschny, C. Reuter, U. Fasel, C. Schulz, H. Riedel, R. Ortner, H.M. “Investigation of the wear mechanism of cubic boron nitride tools used for the machining for compacted graphite iron and grey cast iron” International Journal of Refractory Metals & Hard Materials 18 2000 287 296
- Choudhury, S.K. Rao, I.V.K. Appa “Optimization of cutting parameters for maximizing tool life” International journal of Machine Tools & Manufacture 39 1999 343 353
- Modh, Nikunj R Mistry, G.D. Rathod, K.B. “An experimental investigation to optimize the process parameters of AISI 52100 steel in hot machining” International Journal of Engineering Research and Applications (IJERA) 1 3 483 489
- Hayajneh, Mohammed T. Tahat, Montasser S. Bluhm, Joachim “A study of the Effect of machining parameters on the surface roughness in the end-milling process” Jordan jornal of mechanical and industrial engineering 1 1 September 2007 1 5