This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Methodology for Minimising Emissions Constrained Cold Start Fuel Consumption
Technical Paper
2012-01-0894
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The cold start emissions from gasoline fuelled vehicles are a major challenge when meeting vehicle emissions regulation. Vehicle manufacturers therefore undertake extensive design and testing of the entire exhaust and engine control systems, which is both time consuming and costly. This is particularly an issue with the growing number of control parameters in modern powertrains.
This paper presents a methodology that integrates appropriate physics-based models of the engine and aftertreatment into a numerical optimisation scheme, and is proposed as a possible means of reducing this calibration effort. The methodology is demonstrated over a prescribed drive cycle by identifying the optimal spark timing trajectory that maximises fuel economy while meeting emissions constraints. The trends in the resulting control policy are explained and the results are validated where possible.
Recommended Content
Authors
Citation
Andrianov, D., Manzie, C., and Brear, M., "A Methodology for Minimising Emissions Constrained Cold Start Fuel Consumption," SAE Technical Paper 2012-01-0894, 2012, https://doi.org/10.4271/2012-01-0894.Also In
References
- Seinfeld, J.H. Air Pollution: A Half Century Progress Environmental and Energy Engineering 50 6 1096 1108 2004
- Delphi Worldwide Emissions Standards - Passenger Cars and Light Duty Trucks 2009 http://www.delphi.com/
- MathWorks Model-Based Calibration Toolbox 2011 http://www.mathworks.com/products/mbc/
- AVL AVL CAMEO 2011 http://www.avl.com/cameo/
- Hafner, M. Isermann, R. Multiobjective Optimization of Feedforward Control Maps in Engine Management Systems Towards Low Consumption and Low Emissions Transactions of the Institute of Measurement and Control 25 57 74 2003
- Jankovic, M. Magner, S. Optimization and scheduling for automotive powertrains Proceedings of the American Control Conference 4054 4059 2004
- Popović, D. Janković, M. Magner, S. Teel, A.R. Extremum Seeking Methods for Optimization of Variable Cam Timing Engine Operation IEEE Transactions on Control Systems Technology 14 3 2006
- Dohner, A. “Transient System Optimization of an Experimental Engine Control System Over the Federal Emissions Driving Schedule,” SAE Technical Paper 780286 1978 10.4271/780286
- Cohen, A. Randall, K. Tether, C. Van Voorhies, K. et al. “Optimal Control of Cold Automobile Engines,” SAE Technical Paper 840544 1984 10.4271/840544
- Kang, J.-M. Kolmanovsky, I. Grizzle, J.W. Dynamic Optimization of Lean Burn Aftertreatment Journal of Dynamic Systems, Measurement, and Control 123 153 160 2001
- Kolmanovsky, I. Siverguina, I. Lygoe, B. Optimization of Powertrain Operating Policy for Feasibility Assessment and Calibration: Stochastic Dynamic Programming Approach Proceedings of the American Control Conference 1425 1430 2002
- Sun, J. Sivashankar, N. An Application of Optimization Methods to the Automotive Emissions Control Problem Proceedings of the American Control Conference 1608 1612 1997
- Sanketi, P.R. Zavala, J.C. Hedrick, J.K. Automotive Engine Hybrid Modelling and Control for Reduction of Hydrocarbon Emissions International Journal of Control 79 5 449 464 2006
- Keynejad, F. Manzie, C. Optimization of Cold Start Automotive Fuel Economy Using a Spark Timing Strategy Proceedings of the 45th IEEE Conference on Decision and Control 2006
- Benz, M. Hehn, M. Onder, C.H. Guzzella, L. Model-Based Actuator Trajectories Optimization for a Diesel Engine Using a Direct Method Journal of Engineering for Gas Turbines and Power 133 2011
- Keynejad, F. Manzie, C. Optimal Cold Start Calibration of Spark Ignition Engines IFAC World Congress 2011
- Andrianov, D. Keynejad, F. Dingli, R. Voice, G. et al. “A Cold-Start Emissions Model of an Engine and Aftertreatment System for Optimisation Studies,” SAE Technical Paper 2010-01-1274 2010 10.4271/2010-01-1274
- Sanketi, P.R. Zavala, J.C. Hedrick, J.K. Wilcutts, M. Kaga, T. A Simplified Catalytic Converter Model for Automotive Coldstart Applications with Adaptive Parameter Fitting The 8th International Symposium on Advanced Vehicle Control 2006
- Bérard, F. Cotta, A. Stokes, J. Thring, R. et al. “An Integrated Powertrain (IPT) Model - Stage One,” SAE Technical Paper 2000-01-0864 2000 10.4271/2000-01-0864
- Fussey, P. Goodfellow, C. Oversby, K. Porter, B. et al. “An Integrated Powertrain (IPT) Model - Stage 2: Systems Integration, Supervisory Control and Simulation of Emissions Control Technology,” SAE Technical Paper 2001-01-0938 2001 10.4271/2001-01-0938
- Balenovic, M. Modeling and Model-Based Control of a Three-Way Catalytic Converter PhD thesis Technical University of Eindhoven 2002
- Fiengo, G. Glielmo, L. Santini, S. Serra, G. Control-Oriented Models for TWC-equipped Spark Ignition Engines During the Warm-Up Phase Proceedings of the American Control Conference 1761 1766 2002
- Keynejad, F. Manzie, C. Cold Start Modelling of Spark Ignition Engines Control Engineering Practice 2011 10.1016/j.conengprac.2011.05.005
- Heywood, J.B. Internal Combustion Engine Fundamentals McGraw-Hill 1988
- Pontikakis, G.N. Stamatelos, A.M. Identification of Catalytic Converter Kinetic Model Using a Genetic Algorithm Approach Proceedings Institution of Mechanical Engineers 218 1455 1472 2004
- Andrianov, D.I. Dingli, R.J. Brear, M.J. Manzie, C. The Effect of Grid Resolution and Oxygen Storage in a One-Dimensional Monolithic Three-Way Catalyst Model IFAC Workshop on Engine and Powertrain Control, Simulation and Modeling 2009
- Luus, R. Iterative Dynamic Programming Chapman & Hall/CRC 2000