This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experimental Study of Snow Precipitation Over a Generic Deicing Fluid without Fluid Flow
Technical Paper
2011-38-0045
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Deicing and anti-icing fluids are used to remove and prevent ice formation on aircraft before takeoff. Holdover times (HOT) published by the FAA are used by pilots as guidelines indicating the amount of effective time of a fluid under certain freezing precipitation types. However, the times on these tables are based on endurance time tests involving a visual estimate of failure on a flat plate [1]: when 30% of the fluid is covered with white snow under snow precipitation, although the times have been correlated to aircraft wing tests [2] they do not address the mechanism of fluid failure. To measure and understand the fluid mechanisms conducting to failure, the Anti-icing Materials International Laboratory (AMIL) developed a simplified test with a generic deicing propylene glycol-based fluid. The test consisted of pouring 400 mL of the generic deicing fluid on a 5 dm by 3 dm level flat plate where the plate edges were rimmed with insolated walls to make a waterproof open box. The flat plate covered with deicing fluid was submitted to snow precipitation in the form of regular snow and simulated snow pellets. The snow precipitation intensities and temperatures tested were based on ARP5485. The standard test method for testing snow indoors includes using a heating pad to compensate for the lack of thermal equilibration which occurs in outside with wind and the larger air mass. It was the energy solicited by the fluid melting the snow from the heat pad that was used to develop a model for fluid failure. Three precipitation intensities and eight temperatures with the generic deicing fluid and commercial Type I and Type IV fluids were studied. At fluid failure, snow mass, and energy provided to melt the snow were independent of snow intensity and type of snow, however endurance time and supplied power were dependent on snow intensity but independent of snow type. Visual observations showed that only a fraction of the falling snow in contact with the fluid covering the aluminium plate melts, the unmelted snowflakes descend by gravity into the fluid and accumulate on the aluminium plate surface. The energy to melt the snow was provided by a heating system. The proposed model assumes that enough energy is available to melt all the snow that a deicing fluid is able to absorb under water form and that the water can diffuse rapidly into the deicing fluid due to multiple diffusion sites resulting in an uniform propylene glycol concentration and predicted well the endurance time and the snow mass at fluid failure for a generic deicing and Type I fluid with an error of 7%. A semi-empirical relation was used in the model to evaluate the melting fraction; this relation, based on a phase diagram, can be used to estimate the propylene glycol concentration, the power and the energy as a function of time at the fluid failure. However, the model could not predict the endurance time of Type IV anti-icing fluids.
Authors
Citation
Fortin, G., Enneji, I., Beisswenger, A., and Perron, J., "Experimental Study of Snow Precipitation Over a Generic Deicing Fluid without Fluid Flow," SAE Technical Paper 2011-38-0045, 2011, https://doi.org/10.4271/2011-38-0045.Also In
References
- SAE International Aerospace Recommended Practice “Endurance Time Tests for Aircraft Deicing/Anti-icing Fluids SAE Type II, III, and IV,” SAE Standard ARP5485 July 2007
- Kuperman, M. Moore, R.K. “Deicing/Anti-Icing Fluid Holdover Times Measurements Aircraft and Frosticator Panels Correlation - Snow Condition” United Airlines 22 1995
- Laforte, J.-L. “Outdoors and Laboratory Tests on Holdover Times and Aerodynamic Performance (Type I and II)” SAE G-12 Meeting June 1994
- Bernardin, S. Dubuisson, C. Laforte, J.-L. “Development of Laboratory Test Procedures to Replace Field Anti-Icing Fluid Tests (Snow Equivalence Tests)” TP13141E LIMA/AMIL Chicoutimi, Quebec 110 1997
- Beisswenger, A. Bouchard, K. Laforte, J.-L. “Development of a Procedure for Indoor Testing of Type IV Fluids to Replicate Natural Snow” LIMA/AMIL Chicoutimi, Quebec 2002
- Beisswenger, A. Perron, J. “Indoor Snow Testing of Aircraft Ground Anti-icing Fluids” DOT/FAA/AR-06/14 LIMA/AMIL Chicoutimi, Quebec 2006
- Rassmussen, R. Knight, C. Hills, A. Landolt, S. “Results of Holdover Time Testing of Type IV Anti-Icing Fluids With the Improved NCAR Artificial Snow Generation System” DOT/FAA/AR-99/10 U.S. Department of Transportation, Federal Aviation Administration 1999
- M. Conde Engineering “Thermophysical Properties of Brines Models” http://www.mrc-eng.com/news.htm . 2002 Zurich, Switzerland
- The Dow Chemical Company “A Guide to Glycols” 2003