This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Analysis of Residual Stress Profiles in the Cylinder Web Region of an As-Cast V6 Al Engine Block with Cast-In Fe Liners Using Neutron Diffraction

Journal Article
2011-01-0036
ISSN: 1946-3979, e-ISSN: 1946-3987
Published April 12, 2011 by SAE International in United States
Analysis of Residual Stress Profiles in the Cylinder Web Region of an As-Cast V6 Al Engine Block with Cast-In Fe Liners Using Neutron Diffraction
Sector:
Citation: Sediako, D., D'Elia, F., Lombardi, A., Machin, A. et al., "Analysis of Residual Stress Profiles in the Cylinder Web Region of an As-Cast V6 Al Engine Block with Cast-In Fe Liners Using Neutron Diffraction," SAE Int. J. Mater. Manuf. 4(1):138-151, 2011, https://doi.org/10.4271/2011-01-0036.
Language: English

References

  1. Carrera, E. Rodríguez, A. Talamantes, J. Valtierra, S. Colás, R. “Measurement of Residual Stresses in Cast Aluminum Engine Blocks” Journal of Materials Processing Technology 189 206 210 2007
  2. Li, M. Vijayaraghavan, R. Wolverton, C. Allison, J. “Simulation of Local Microstructures and Thermal Growth of a Cast 319 Aluminum Alloy Component” 1st International Symposium on Metallurgical Modelling for Aluminum Alloys USA October 13 15 2003
  3. Noyan, I. C. Cohen, J. B. “Residual Stress: Measurement by Diffraction and Interpretation” Springer-Verlag New York 0-387-96378-2 1987
  4. Society for Experimental Mechanics “Handbook of Measurement of Residual Stresses” Fairmont Press Upper Saddle River, NJ 0-881-73229-X 1996
  5. Avallone, E. A. Baumeister, T. III Sadegh, A. M. “Marks' Standard Handbook for Mechanical Engineers 11th Edition” McGraw-Hill Companies, Inc. New York 0-07-142867-4 2007
  6. Davis, J. R. “ASM Specialty Handbook: Aluminum and Aluminum Alloys” ASM International Materials Park, Ohio 0-87170-496-X 1993
  7. Wiesner, D. J. Watkins, T. R. Ely, T. M. Spooner, S. Hubbard Williams, J. C. “Residual Stress Measurements of Cast Aluminum Engine Blocks using Diffraction” JCPDS - International Centre for Diffraction Data, Advances in Analysis 48 136 142 2005
  8. Flemings, M. “Solidification Processing” McGraw-Hill Companies, Inc. New York 0-07-021283-1 1974
  9. Campbell, J. “Castings” Elsevier Butterworth-Heinemann Oxford 0-7506-4790-6 2003
  10. Vazquez-Lopez, C. Calderone, A. Rodriguez, M. E. Velasco, E. Cano, S. Colas, R. Valtierra, S. “Influence of dendrite arm spacing on the thermal conductivity of an aluminum-silicon casting alloy” Journal of Materials Research 15 85 91 2000
  11. Lasa, L. Rodriguez-Ibabe, J. “Evolution of the Main Intermetallic Phases in Al-Si-Cu-Mg Casting Alloys during Solution Heat Treatment” Journal of Materials Science 39 1343 1355 2004
  12. Apelian, D. Sigworth, G. Whaler, K. “Assessment of Grain Refinement and Modification of Al-Si Foundry Alloys by Thermal Analysis” AFS Transactions 92 297 307 1984
  13. Li, Z. Samuel, A. Samuel, F. Ravindran, C. Valtierra, S. “Effect of alloying elements on the segregation and dissolution of CuAl 2 phase in Al-Si-Cu 319 alloys” Journal of Materials Science 38 1203 1218 2003
  14. Totten, G. “Handbook of Residual Stress and Deformation of Steel” ASM International Materials Park, Ohio 0871707292 2002

Cited By