This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Modeling and Manufacturing of Turbocharger Compressors
Technical Paper
2010-01-1219
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
While turbocharging has existed for a full century, its significance has increased very rapidly in the past few decades. At the heart of good turbocharger performance is an excellent compressor stage, or stages, that must be efficient, stable, lightweight, and inexpensive to manufacture. Based on decades of design experience, the performance modeling of these stages is presented, techniques for design optimization are reviewed, and means for rapid machining are explained. The reader will gain insight to some of the most critical aspects of compressor design.
Recommended Content
Authors
Citation
Japikse, D., Osborne, C., Klein, P., Pope, W. et al., "Modeling and Manufacturing of Turbocharger Compressors," SAE Technical Paper 2010-01-1219, 2010, https://doi.org/10.4271/2010-01-1219.Also In
References
- Watson, N. Janota, M. S. Turbocharging the Internal Combustion Engine Fluid Dynamics Institute 1977
- Baines, N. C. Fundamentals of Turbocharging Concepts ETI, Inc. Wilder, VT 2005
- Sun, H. et al. “Challenges and Opportunities in Turbocharger Technology for Future Diesel LTC” GPC2009 Global Powertrain Congress Troy, MI November 4-5 2009
- Arnold, S. “Single Sequential Turbocharger: A New Boosting Concept for Ultra-Low Emission Diesel Engines,” SAE Int. J. Engines 1 1 232 239 2008
- Stodola, A. Loewenstein, L. C. Steam and Gas Turbines Peter Smith New York 1945 83 328
- Japikse, D. “Turbomachinery Performance Modeling,” SAE Technical Paper 2009-01-0307 2009
- Japikse, D. Centrifugal Compressor Design and Performance Concepts ETI, Inc. Wilder, VT 1996
- Sloteman, D. P. Cooper, P. Dussourd, J. L. “Control of Backflow at the Inlets of Centrifugal Pumps and Inducers” Proceedings of the First International Pump Symposium Turbomachinery Laboratory, Texas A&M University 9 22
- Chapman, D. C. Centrifugal Compressors, Flow Phenomena and Performance, Model 250-C30/C28B Compressor Development AGARD Conference Proceedings No. CP-282
- Japikse, D. Baun, D. O. “Secondary Flow Control System” U.S. Patent No. 7 025 557 April 11 2006
- Galerkin, Y. B. Mitrofanov, V. P. “The Modern Optimizing Design Methods Implementation to the Development of a New Generation of Centrifugal Model Stages” Khimicheskoe I Neftegazovoe Mashinostroenie (Khim I Neft Mashinostr) 1995 11 36 40 1995
- Japikse, D. “Expedited Agile System Design and Redesign Approach for Industrial Pumps,” 2002 International iSIGHT Users' Conference Arlington, VA July 16-18 2002
- Japikse, D. “Systematic Optimization for Turbomachinery Design and Redesign,” 2003 JSME Fluid Engineering Conference Osaka, Japan September 19-20 2003
- Amano, R. S. Xu, C. “Development of the Efficient Single Centrifugal Compressor for Aircraft Engineers” 44th AIAA Aerospace Sciences Meeting and Exhibit Reno, NV, USA January 9-12 2006
- Ji, G-F. Gui, X-M. “Blading Design Method for Axial/Centrifugal Compressor Airfoils Using Arbitrary Camber Lines” Journal of Aerospace Power , Hangkong Dongli Xuebao 24 1 150 156 2009
- Yiu, K. F. C. Zangeneh, M. “3D Automatic Optimization Strategy for Design of Centrifugal Compressor Impeller Blades” 1998 International Gas Turbine & Aeroengine Congress & Exhibition Stockholm, Sweden June 2-5 1998
- Zangeneh, M. Schleer, M. Ploger, F. Hong, S. S. Roduner, C. Ribi, B. Abhari, R. S. “Investigation of an Inversely Designed Centrifugal Compressor Stage Part 1: Design and Numerical Verification” 2003 ASME Turbo Expo Atlanta, GA, USA June 16-19 2003
- Bonaiuti, D. Zangeneh, M. “On the Coupling of Inverse Design and Optimization Techniques for Turbomachinery Blade Design” ASME 51st Turbo Expo Barcelona, Spain May 6-11 2006
- Fan, H. Wang, S. Xi, G. “Optimization of the Blades for Turbomachine by Genetic Algorithm” Acta Aeronautica et Astronautica Sinica 20 1 47 51 1999
- Lee, Y-L. Luo, L. Bein, T. W. “Direct Method for Optimization of a Centrifugal Compressor Vaneless Diffuser” Journal of Turbomachinery 123 1 73 80 2001
- Saladino, A. J. Bielecki, S. J. “Streamlining of the Radial Inlet Design Process for Centrifugal Compressors” 2002 ASME International Mechanical Engineering Congress and Exposition New Orleans, LA, USA November 17-22 2002
- Osborne, C. Platt, M. J. Weitzman, P. S. Denus, K. “Multi-Disciplinary Optimization Applied to a Turbocharger Compressor Impeller” IXth International Conference Rotary Fluid-Flow Machines Rzeszow, Poland October 16-18 2003
- Japikse, D. Platt, M. J. “Optimization in Component Design and Redesign,” 10th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-10) Honolulu, Hawaii March 7-11 2004
- Li, J. Li, G. Feng, Z. Liu, L. “Multiobjective Optimization Approach to Turbomachinery Blades Design” ASME Turbo Expo 2005 Reno-Tahoe, NV, USA
- Sun, H. Shin, H. Lee, S. “Analysis and Optimization of Aerodynamic Noise in a Centrifugal Compressor” Journal of Sound and Vibration 289 4-5 999 1018 2006
- Platt, M. J. Yu, M. Marsh, M. “Multidisciplinary Optimization of a LH2 Turbopump Design in an Agile Engineering Environment” AIAA Joint Propulsion Conference and Exhibit Huntsville, AL July 20-23 2003
- Ashihara, K. Goto, A. Guo, S. Okamoto, H. “Optimization of Microturbine Aerodynamics Using CFD, Inverse Design and FEM Structural Analysis” 2004 ASME Turbo Expo Vienna, Austria June 14-17 2004
- Japikse, D. “Developments in Agile Engineering for Turbomachinery” 9th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC) Honolulu, HI February 10-14 2002 Proceedings of ASME FEDSM'02 2002 ASME Fluids Engineering Division Summer Meeting Montreal, Canada July 14-18 2002
- Levine, A. R. Amidon, B. W. “Method for Multi-Criteria Flank Milling of Ruled Surfaces” U.S. Patent No. 5 391 024 February 21 1995