This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Hydrogen as a Combustion Modifier of Ethanol in Compression Ignition Engines
Technical Paper
2009-01-2814
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Ethanol, used widely as a spark-ignition (SI) engine fuel, has seen minimal success as a compression ignition (CI) engine fuel. The lack of success of ethanol in CI engines is mainly due to ethanol's very low cetane number and its poor lubricity properties. Past researchers have utilized nearly pure ethanol in a CI engine by either increasing the compression ratio which requires extensive engine modification and/or using an expensive ignition improver.
The objective of this work was to demonstrate the ability of a hydrogen port fuel injection (PFI) system to facilitate the combustion of ethanol in a CI engine. Non-denatured anhydrous ethanol, mixed with a lubricity additive, was used in a variable compression ratio CI engine. Testing was conducted by varying the amount of bottled hydrogen gas injected into the intake manifold via a PFI system. The hydrogen flowrates were varied from 0 - 10 slpm. The engine was operated at compression ratios varying from 19:1 to 24:1 and intake air temperatures ranging from 80°C to 120°C.
To prevent injection system lubrication failure, castor oil and lauric acid were tested in various blends with ethanol according to ASTM D975. It was found that 2% by volume of lauric acid provided a wear scar diameter of 200 μm, very close to the diesel fuel wear scar diameter of 195 μm at 25°C, and was chosen as the lubricity additive.
Small amounts of hydrogen enabled ethanol operation at a compression ratio of 19:1 and an intake temperature of 80°C. This was a condition that was not sustainable without hydrogen injection. Adding hydrogen with the intake air advanced the start of combustion (SOC) timing for many of the conditions tested. The relatively small amounts of hydrogen necessary could be provided by an onboard ethanol reformer. Further work is necessary to determine why the hydrogen injection causes this SOC advance.
Recommended Content
Authors
Topic
Citation
Bika, A., Franklin, L., and Kittelson, D., "Hydrogen as a Combustion Modifier of Ethanol in Compression Ignition Engines," SAE Technical Paper 2009-01-2814, 2009, https://doi.org/10.4271/2009-01-2814.Also In
References
- Yilmaz, N. Donaldson, A. B. Jones, A. Some Perspectives on Alcohol Utilization in a Compression Ignition Engine SAE Technical Paper 2005-01-3135 2005
- Goering, C. E. Parcell, R. T. Ritter, C. P. Hydrated Ethanol as a Fuel for a DI, CI Engine Transactions of the ASAE 41 1998
- Nagarajan, G. Rao, A. N. Renganarayanan, S. Emission and Performance Characteristics of Neat Ethanol Fuelled DI Diesel Engine Int. J. of Ambient Energy 23 149 158 2002
- Hardenberg, H. O. Schaefer, A. J. The Use of Ethanol as a Fuel for Compression Ignition Engines SAE Technical Paper 811211 1981
- King, L. J. Prakash, C. B. Field Trials of Ethanol in Transit Buses SAE Technical Paper 922272 1992
- Estefan, R. M. Brown, J. G. Evaluation of Possible Methanol Fuel Additives for Reducing Engine Wear and/or Corrosion SAE Technical Paper 902153 1990
- Lacey, P. I. Howell, S. A. Fuel Lubricity Reviewed SAE Technical Paper 982567 1998
- Lacey, P. I. Naegeli, D. W. De La Cruz, J. L. Whalen, M. V. Lubricity of Volatile Fuels for Compression Ignition Engines SAE Technical Paper 2000-01-1804 2000
- Barbour, R. H. Rickeard, D. J. Elliot, N. G. Understanding Diesel Lubricity SAE Technical Paper 2000-01-1918 2000
- Lacey, P. I. Westbrook, S. R. Fuel Lubricity Additive Evaluation U.S. Army TARDEC Contract Interim Report TFLRF No. 323 1997
- Lee, D. Hochgreb, S. Keck, J. C. Autoignition of Alcohols and Ethers in a Rapid Compression Machine SAE Technical Paper 932755 1993
- Bollentin, J. W. Wilk, R. D. Autoignition Characteristics of Ethanol SAE Technical Paper 961175 1996
- Schaefer, A. J. Hardenberg, H. O. Ignition Improvers for Ethanol Fuels SAE Technical Paper 810249 1981
- Tsolakis, A. Hernandez, J. J. Megartitis, A. Crampton, M. Dual fuel diesel engine operation using H2. Effect on particulate emissions Energy 8 Fuels 19 418 425 2005
- Panuccio, G. J. Williams, K. A. Schmidt, L. D. Contributions of Heterogeneous and Homogeneous Chemistry in the Catalytic Partial Oxidation of Octane Isomers and Mixtures on Rhodium Coated Foams Chem. Eng. Sci 61 4207 4219 2006
- Nilesen, O. B. Qvale, B. Sorenson, S. Ignition Delay in the Dual Fuel Engine SAE Technical Paper 870589 1987
- Liu, Z. Karim, G. A. The Ignition Delay period in Dual Fuel Engines SAE Technical Paper 950466 1995
- Gunea, C. Razavi, M. R. M Karim, G. A. The Effects of Pilot Fuel Quality on Dual Fuel Engine Ignition Delay SAE Technical Paper 982453 1998
- Karim, G. A. Jones, W. Raine, R. R. An Examination of the Ignition Delay Period in Dual Fuel Engines SAE Technical Paper 892140 1989
- Curran, H. J. Gaffuri, P. Pitz, W. J. Westbrook, C. K. A Comprehensive Modeling Study of n-Heptane Oxidation Combustion and Flame 114 149 177 1998
- Marinov, N. M. A Detailed Chemical Kinetic Model for High Temperature Ethanol Oxidation Int. J. Chem. Kinetics 31: 1999
- Henein, N. A. Akasaka, Y. Effect of Physical Properties and Composition on Fuels on Autoignition and Cetane Rating SAE Technical Paper 871617 1987
- Westbrook, C. K. Chemical Kinetics of Hydrocarbon Ignition in Practical Combustion Systems Proceedings of the Combustion Institute 1563 1577 2000