This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Investigation into Different DPF Regeneration Strategies Based on Fuel Economy Using Integrated System Simulation
Technical Paper
2009-01-1275
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
An integrated system model containing sub-models for a multi-cylinder diesel engine, NOx and soot(PM) emissions, diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) has been developed to simulate the engine and aftertreatment systems at transient engine operating conditions. The objective of this work is two-fold; ensure correct implementation of the integrated system level model and apply the integrated model to understand the fuel economy trade-off for various DPF regeneration strategies.
The current study focuses on a 1.9L turbocharged diesel engine and its exhaust system. The engine model was built in GT-Power and validated against experimental data at full-load conditions. The DPF model is calibrated for the current engine application by matching the clean DPF pressure drop for different mass flow rates. Load, boost pressure, speed and EGR controllers are tuned and linked with the current engine model.
DPF soot loading and the impact of backpressure on engine performance is captured. DPF regeneration studies are carried out by using fuel injection ahead of the DOC and various regeneration strategies are explored. Delaying regeneration and increased loading of PM in DPF is of particular interest, as it causes an increase in back pressure and subsequently higher fuel penalty. During regeneration there is an extra penalty on fuel economy due to fuel injection ahead of the DOC.
This study shows the effect of various DPF loading and regeneration strategies based on fuel economy. For a sample case study considered, fuel penalty associated with regeneration is reduced with delayed regeneration and higher PM loadings of the DPF. An energy budget analysis shows that this is due to the energy required to heat the substrate to soot regeneration temperature.
Recommended Content
Authors
Topic
Citation
Singh, N., Rutland, C., Foster, D., Narayanaswamy, K. et al., "Investigation into Different DPF Regeneration Strategies Based on Fuel Economy Using Integrated System Simulation," SAE Technical Paper 2009-01-1275, 2009, https://doi.org/10.4271/2009-01-1275.Also In
References
- Rutland, C. J. England, S. B. Foster, D. E. He, Y. “Integrated Engine, Emissions, and Exhaust Aftertreatment System Level models to Simulate DPF Regeneration.” SAE Paper No. 2007-01-3970 2007
- Bayer, J. M. “Zero-Dimensional Direct-Injection Spray and Particulate emission modeling” Masters Thesis University of Wisconsin-Madison 2002
- Bayer, J. M Foster, D. E “Zero Dimensional Soot Modeling” SAE Paper No. 2003-01-1070 2003
- Indranil, Brahma Rutland, Chris Foster David He Yongsheng “A new approach to system level soot modeling” SAE Paper No. 2005-01-1122 2005
- England, S. B “Development of an Integrated Diesel Engine, Emission, and Aftertreatment System Level Model” Masters thesis University of Wisconsin-Madison 2006
- Sampara C. J. Bissett E. J. Chmielewski M. Assanis D. “Global Kinetics for Platinum Diesel Oxidation Catalysts,” Ind. Eng. Chem. Res. 2007 46 7993 8003
- He, Y. “Development of an Integrated Diesel Exhaust Aftertreatment Simulation Tool with Applications in Aftertreatment System Architecture Design” SAE Paper No. 2007-01-1138 2007
- He, Y. Personal Communication
- Kapparos, D. J. Brahma, I. Strzelec, A Rutland, Chris Foster David He Yongsheng “Integration of Diesel Engine, Exhaust System, Engine Emissions and Aftertreatment Device Models” SAE Paper No. 2005-01-0947 2005
- Huynh, C. T. Johnson, J. H. Yang, S. L. Bagley, S. T. Warner, J. R. “A one dimensional Computational Model for Studying the filtration and Regeneration Characteristics of a Catalyzed WallFlow Diesel Particulate Filter” SAE Paper No. 2003-0-0841 2003
- Strzelec, A. “Development of a System Level Soot-NOx reduction filter Aftertreatment Device Model” Masters Thesis University of Wisconsin-Madison 2006
- GT-Power User Manual and Guide Tutorials GT-Version 6.2 Information about basic GT-Structure
- Eriksson, L. “P-, PI- and PID Control- Automation and Control Engineering Laboratory Course” Helsinki University of Technology 2002
- Franklin, G. F. Powell, J. D. Emami-Naeni, A. Feedback Control of Dynamic Systems 5th Upper Saddel River, NJ Prentice Hall 2002
- Singh, N. Johnson, J. H. Parker, G. G. Yang, S. L. ” Vehicle Engine Aftertreatment System Simulation (VEASS) Model: Application to a Controls Design Strategy for Active Regeneration of a Catalyzed Particulate Filter” SAE Paper No 2005-01-0970 2005
- Singh P. Thalagavara A. M. Naber J. D. Johnson J. H. Bagley S. T. “An Experimental Study of Active Regeneration of an Advanced Catalyzed Particulate Filter by Diesel Fuel Injection Upstream of an Oxidation Catalyst” SAE Paper No. 2006-01-0879 2006
- Eastwood, P. “ Critical Topics in Exhaust Gas Aftertreatment ” Research Studies Press Ltd Baldock, Hertfordshire, England 2000