This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A PDF-Based Model for Full Cycle Simulation of Direct Injected Engines
Technical Paper
2008-01-1606
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
In one-dimensional engine simulation programs the simulation of engine performance is mostly done by parameter fitting in order to match simulations with experimental data. The extensive fitting procedure is especially needed for emissions formation - CO, HC, NO, soot - simulations.
An alternative to this approach is, to calculate the emissions based on detailed kinetic models. This however demands that the in-cylinder combustion-flow interaction can be modeled accurately, and that the CPU time needed for the model is still acceptable. PDF based stochastic reactor models offer one possible solution. They usually introduce only one (time dependent) parameter - the mixing time - to model the influence of flow on the chemistry. They offer the prediction of the heat release, together with all emission formation, if the optimum mixing time is given. Hence parameter fitting for a number of kinetic processes, that depend also on the in cylinder flow conditions is replaced by a single parameter fitting for the turbulent mixing time.
In this work a PDF based model was implemented and coupled to the full cycle engine simulation tool, WAVE, and calculations were compared to engine experiments. Modeling results show good agreement with the experiments and show that PDF based Dl models can be used for fast and accurate simulation of Dl engine emissions and performance.
Recommended Content
Authors
Citation
Tunér, M., Pasternak, M., Mauss, F., and Bensler, H., "A PDF-Based Model for Full Cycle Simulation of Direct Injected Engines," SAE Technical Paper 2008-01-1606, 2008, https://doi.org/10.4271/2008-01-1606.Also In
References
- Vibe (Wiebe), I. Berlin 1964
- Watson, N. Pilley, A. D. Marzouk, M. “A Combustion Correlation for Diesel Engine Simulation” SAE 800029
- Patterson, M.A. Reitz, R.D. “Modeling the Effect of Fuel Spray Characteristics on Diesel Engine Combustion and Emission” SAE 980131
- Pitsch, H. Barths, H. Peters, N. “Threedimensional modeling of NOx and soot formation in DI-Diesel engines using detailed chemistry based on the interactive flamelet approach” SAE 962057
- Steiner, R. Bauer, C. Kruger, C. Otto, F. Maas, U. “3D-simulation of DI-diesel combustion applying a progress variable approach accounting for complex chemistry” SAE 2004-01-0106
- Lehtiniemi, H. Mauss, F. Magnusson, I. Balthasar, M. “Modeling Diesel Engine Combustion with Detailed Chemistry Using a Progress Variable Approach” SAE 2005-01-3855
- Vermorel, O. Richard, S. Colin, O. Angelberger, C. Benkenida, A. Veynante, D. “Multi-cycle LES simulations of flow and combustion in a PFI SI 4-valve production engine” SAE 2007-01-0151
- Lehtiniemi, H. Zhang, Y. Rawat, R. Mauss, F. “Efficient 3-D CFD Combustion Modeling with Transient Flamelet Models” SAE 2008-01-0957
- Montorsi, L. Mauss, F. Bianchi, G. M. Bhave, A. Kraft, M. 2003 Analysis of the HCCI Combustion of a Turbocharged Truck Engine Using a Stochastic Reactor Model ASME ICE Division, ICES-2003-681
- Amnéus, P. Tunér, M. Mauss, F. Collin, R. Nygren, J. Richter, M. Aldén, M. Kraft, M. Bhave, A. Hildingsson, L. Johansson, B. “Formaldehyde and Hydroxyl Radicals in an HCCI Engine - Calculations and LIF-Measurements” SAE 2007-01-0049
- Gogan, A. Lehtiniemi, H. Sundén, B. Mauss, F. “Stochastic Model for the Investigation of the Effect of Turbulent Mixing on Engine Knock” SAE 2004-01-2999
- Tunér, M. Blurock, E. S. Mauss, F. “Phase Optimized Skeleton Mechanisms for Stochastic Reactor Models for Engine Simulation” SAE 2005-01-3813
- Heywood, J. B. “Internal Combustion Engine Fundamentals” 506 McGraw Hill New York 1988
- Challen, B. Baranescu, R. “Diesel Engine Reference Book” Second SAE International 1999
- Warnatz, J. Maas, U. Dibble, J. W. “Combustion: Physical and Chemical Fundamentals, Modeling and Simulation, Experiments, Pollutant Formation book reference” Springer 2006
- Su, H. Vikhansky, A. Mosbach, S. Kraft, M. Bhave, A. Kim, K. Kobayashi, T. Mauss, F. “A computational study of an HCCI engine with direct injection during gas exchange” Combustion and Flame 147 118 132 2006
- Mosbach, S. Su, H. Kraft, M. Bhave, A. Wang, Z. Wang, J. Mauss, F. “Dual Injection HCCI Engine Simulation using a Stochastic Reactor Model.” The International Journal of Engine Research 8 1 41 50 2007
- Samuelsson, K. Gogan, A. Netzell, K. Lehtiniemi, H. Sunden, B. Mauss, F. “Modeling Diesel Engine Combustion and Pollutant Formation Using a Stochastic Reactor Model Approach” Intl. Conf. Clean Diesel Combustion Lund 2005
- Ricardo, Inc. Wave 7.1 User's Manual www.ricardo.com
- Kraft, M. Stochastic Modelling of Turbulent Reacting Flow in Chemical Engineering 1998 6 391 1 109 VDI Verlag, Fortschrittsberichte des VDI
- Bhave, A. Balthasar, M. Kraft, M. Mauss, F. “Analysis of a natural gas fuelled homogeneous charge compression ignition engine with exhaust gas recirculation using a stochastic reactor model” Int. J. Engine Res. 5 1 93 103 2004
- Yang, B. Pope, S. B. “An investigation of the accuracy of manifold methods and splitting schemes in the computational implementation of combustion chemistry” Combustion and Flame 112 16 32 1998
- Curl, R. L. Dispersed Phase Mixing: I. Theory and Effects in Simple Reactors A.I.Ch.E. Journal 9 2 175 181 1963
- Woschni, G. “A Universally Applicable Equation for the Instantaneous Heat Transfer Coefficient in the Internal Combustion Engine” SAE 670931
- Ahmed, S. S. Mauss, F. Moréac, G. Zeuch, T. “A comprehensive and compact n-heptane oxidation model derived using chemical lumping” Phys. Chem. Chem. Phys. 9 1107 1126 2007