This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Pre-Turbocharger-Catalyst - Catalytic Performances on an Euro V Type Diesel Engine and Robust Design Development
Technical Paper
2008-01-0768
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Future emission legislation and new diesel engine technology tighten the requirements for modern diesel vehicle exhaust after-treatment systems. In particular, the oxidation catalyst system requires more efficiency to treat increasing raw emissions of HC and CO at low exhaust gas temperatures resulting from advanced combustion processes. This represents a big challenge for all developers today where the cost of raw materials continues to rise.
Splitting the oxidation catalyst volume into two parts and mounting a very small part in front of a turbocharger on Euro III or Euro IV Diesel engines has been proved very efficient: Light off and maximum pollutant conversion rates were improved. New results gained with Pre Turbocharger Catalyst (PTC) on a Euro V type diesel engine are confirming previous observations.
The complete after-treatment system of today's vehicles should be designed and developed for the whole life of the vehicle. Due to its position in front of the turbine any failure of the PTC, in either the metal substrate or of the coating, would result in particularly severe consequences due to turbine damage and/or loss of turbine function. A robust design for the metal substrate has been defined with the help of Finite Element simulation of thermal stress and has then been validated on the component test bench.
Recommended Content
Authors
Topic
Citation
Konieczny, R., Müller, W., Cherington, B., Presti, M. et al., "Pre-Turbocharger-Catalyst - Catalytic Performances on an Euro V Type Diesel Engine and Robust Design Development," SAE Technical Paper 2008-01-0768, 2008, https://doi.org/10.4271/2008-01-0768.Also In
References
- Tableau de bord automobile Année 2006 9 Comité des Constructeurs Français d'Automobiles (CCFA)
- Coma G. Gastaldi P. Hardy JP. Maroteaux D. “HCCI combustion: dream or reality?” Aachener Kolloquium Fahrzeug - und Motorentechnik 2004
- Dupont Henri Passilly Laetitia “Systematic Approach for Compliance with the Future Emission Legislation for Diesel Engines” Diesel Engine 2006 May 31 June 1 2006 Ecole Centrale de Lyon
- Reizig Meike Brück Rolf Konieczny Roman Treiber Peter GmbH Emitec “New Approaches to Catalyst Substrate Application for Diesel Engines” SAE 2001-01-0189
- Jacob E. Dr. Döring Dipl.-lng. A. MAN Nutzfahrzeuge AG, Nürnberg: AGD-KAT: Abgasnachbehandlungssystem zur simultanen Kohlenstoffpartikel-Oxidation und NOx-Reduktion für Euro 4/5-Nfz-Dieselmotoren 21. Internationales Wiener Motorensymposium, VDI-Fortschritt Berichte 12 2000
- Saroglia Gianpiero Basso Giovanni Presti Manuel Reizig Meike Stock Holger “Application of New Diesel Aftertreatment Strategies on a Production 1.9L Common-Rail Turbocharged Engine” SAE 2002-01-1313
- Carberry Brendan Grasi Georg Guerin Stephane Jayat Francois Konieczny Roman ‘Pre Turbocharger Catalyst - Fast Catalyst Light-Off Evaluation’ SAE 2005-01-2142
- Sanguedolce Andrea Boretto Gianmarco Basso Giovanni Cipolla Giovanni Gionannini Alberto Tonetti Marco “Emission and Performance Assessment of an Advanced Diesel Pre-Turbo catalyst System designed for a Passenger Car Diesel Engine Application” 4.Internationales AVL-Forum Abgas-und Partikel-Emissionen Ludwigsburg März 2006
- Maus Wolfgang Brück Rolf Kaiser Friedrich W: “Fortschrittliche PKW Dieselabgasnachbehandlung; Potenzial für niedrigste Emissionsgrenzwerte?” 23. Internationales Wiener Motorensymposium 25-26 April 2002
- Jayat Francois Pace Lorenzo Konieczny Roman „Vorturboladerkatalysatoren - Anforderungen aus aufladetechnischer Sicht sowie zukünftiger, innovativer Abgasnachbehandlungskonzepte” 12. Aufladetechnische Konferenz 2007 September 27 28 Dresden
- 13 th DEER conference Detroit
- Nagel Thomas Kramer Jan Presti Manuel Schatz Axel Jürgen Breuer Salzman Ron Scaparo John A. Montalbano Andrew J. “A new Approach of accelerated Life Testing for Metallic Catalytic Converters” SAE 2004-01-0595