This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
3D Simulations And Experimental Validation of High EGR - PHCCI Combustion
Technical Paper
2007-24-0037
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The present work addresses the possibility to correctly simulate Partial Homogeneous Charge Compression Ignition (PHCCI) combustion, obtained by the application of EGR up to 60% without using detailed kinetic models. In particular, the laminar and turbulent time characteristic model has been analyzed and improved. The study illustrates the prediction capabilities that can be achieved with such an approach.
The paper reports the results obtained from the simulation of a single cylinder research engine and a four-cylinder diesel engine to verify the validity of the proposed method independently of engine geometry and configuration. All numerical results are compared with experimental pressure traces and rates of heat release, as well as with NOx and soot emissions over a wide range of operating conditions. With the modified characteristic time model, realistic simulations of engine combustion up to EGR values of about 60% have been obtained for both engines. In particular, simulations quantitatively predicted the reduction of the in-cylinder peak pressure and NO emissions as well as the increase of soot as the EGR rate was increased.
Recommended Content
Authors
- A. de Risi - Università del Salento, Dipartimento di Ingegneria dell'Innovazione
- S. Zurlo - Università del Salento, Dipartimento di Ingegneria dell'Innovazione
- T. Donateo - Università del Salento, Dipartimento di Ingegneria dell'Innovazione
- D. Laforgia - Università del Salento, Dipartimento di Ingegneria dell'Innovazione
Topic
Citation
de Risi, A., Zurlo, S., Donateo, T., and Laforgia, D., "3D Simulations And Experimental Validation of High EGR - PHCCI Combustion," SAE Technical Paper 2007-24-0037, 2007, https://doi.org/10.4271/2007-24-0037.Also In
References
- Montgomery, D.T. Reitz, R.D. “Six-Mode Cycle Evaluation of the Effect of EGR and Multiple Injections on Particulate and NO x Emissions from a D.I. Diesel Engine,” SAE Paper 960316 1996
- Heywood, J.B. Internal Combustion Engine Fundamentals Mc Graw-Hill New York 1988
- Abd-Alla, G.H. “Using Exhaust Gas Recirculation in Internal Combustion Engines: a Review,” Energy Conversion and Management 43 1027 1042 2002
- Han, Z. Uludugan, A. Hampson, G.J. Reitz, R.D. “Mechanism of Soot and NO x Reduction Using Multiple Injection in Diesel Engine,” SAE Technical Paper 960633 1996
- Chan, M. Das, S. Reitz, R.D. “Modeling Multiple Injection and EGR Effects on Diesel Engine Emissions,” SAE Paper 972864 1997
- Abraham, J. Bracco, F.V. Reitz, R.D. “Comparisons of Computed and Measured Premixed Charge Engine Combustion,” Combust. Flame 60 309 322 1985
- Kong, S.C. Ayoub, N. Reitz, R.D. “Modeling Combustion in Compression Ignition Homogeneous Charge Engines,” SAE Paper 910267 1991
- Xin, J. Montgomery, D. Han, Z. Reitz, R.D. “Multidimensional Modeling of Combustion for a Six-Mode Emission Test Cycle of a DI Diesel Engine,” Journal of Engineering for Gas Turbine and Power 119 683 691 1997
- De Risi, A. Donateo, T. Laforgia, D. “A New Advanced Approach to the Design of Combustion Chambers in Diesel Engines” Int. J. Vehicle Design 41 1/2/3/4 165 187 2006
- Richards, K.J. Subramaniam, M.N. Reitz, R.D. Lai, M.C. Henein, N.A. Miles, P.C. “Modeling the Effects of EGR and Injection Pressure on Emissions in a High-Speed Direct-Injection Diesel Engine,” SAE Paper 2001-01-1004 2001
- Henein, N.A. Lai, M.C. Singh, I. Wang, D. Liu, L. “Emissions Trade-Off and Combustion Characteristics of a High-Speed Direct-Injection Diesel Engine,” SAE Paper 2001-01-0197 2001
- Zhu, Y. Zhao, H. Ladommatos, N. “Computational Study of the Effects of Injection Timing, EGR and Swirl Ratio on a HSDI Multi-Injection Diesel Engine Emission and Performance,” SAE Paper 2003-01-0346 2003
- Zhu, Y. Zhao, H. Melas, D.A. Ladommatos, N. “Computational Study of the Effects of the ReEntrant Lip Shape and Toroidal Radii of Piston Bowl on a HSDI Diesel Engine's Performance and Emission,” SAE Paper 2004-01-0118 2004
- de Risi, A. Donateo, T. Laforgia, D. “Theoretical Investigation on Variable Density Sprays” Atomization and Sprays 12 329 358 2002
- de Risi, A. Donateo, T. Laforgia, D. “CFD Modeling of Pilot Injection and EGR in DI Diesel Engines,” ICEF2004-837 Fall Technical Conference Long Beach CA, USA October 24-27 2004
- Halstead, M. Kirsh, L. Quinn, C. “The Autoignition of Hydrocarbon Fuels at High Temperature and Pressure - Fitting of a Mathematical Model,” Combustion Flame 30 45 60 1977
- Bergeron, C. Hallett, W.L.H. “Ignition Characteristics of Liquid Hydrocarbon Fuels as Single Droplets,” The Canadian Journal of Chemical Engineering 67 142 149 1989
- Kong S. Han Z. Reitz R.D. “The Development and Application of a Diesel Ignition and Combustion Model for Multidimensional Engine Simulation,” SAE Paper 950278 1995
- Hiroyasu, H. Nishida, K. “Simplified Three Dimensional Modeling of Mixture Formation and Combustion in a D.I. Diesel Engine,” SAE Paper 890269 1989
- Nagle, J. Strickland-Constable, R. F. “Oxidation of Carbon between 1000-2000 °C,” Procedure of the Fifth Carbon Conference 1 Pergammon Press 1962
- Heywood, J.B. “Pollutant Formation and Control in Spark-Ignition Engines,” Progress in Energy and Combustion Science 1 135 164 1976
- Zheng, M. Reader, G. T. Hawley, J. G. “Diesel engine exhaust gas recirculation - a review on advanced and novel concepts,” Energy Conversion and Management 45 883 900 2004
- Shi Lei Cui Yi Deng Kangyao Pen Haiyong Chen Yuanyuan “Study of low emission homogeneous charge compression ignition engine using combined internal and external exhaust gas recirculation,” Energy 31 2665 2676 2006
- Donateo, T. de Risi, A. Laforgia, D. “The Use of Φ-t Maps for Soot Prediction in Engine Modeling,” International Multidimensional Engine Modeling User's Group Meeting Detroit MI, USA April 10 2005