This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Testing of a Freeze-proof Condenser for the Tracker Thermal Control System on AMS-02
Technical Paper
2007-01-3238
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The paper describes freezing and pressure tests required to develop a freeze-proof condenser for the Tracker Thermal Control System (TTCS). The TTCS is a mechanically pumped two-phase carbon-dioxide loop dedicated to control the temperature of the Tracker electronics. The TTCS is part of the Alpha Magnetic Spectrometer planned aboard the truss of the International Space Station (ISS). The TTCS collects the heat at two evaporators and rejects it at two radiators. In case of an accidental power-down of the AMS02 experiment, resulting in a loss of radiator heater control, the Tracker radiators and the connected TTCS-condensers may cool down as low as −120ºC, which is well below the CO2-freezing point (−56ºC@3MPa). During uncontrolled radiator heat-up and thawing of the solid CO2, liquid CO2 can be trapped in between solid parts resulting in high pressures. To withstand these high pressures, a high-pressure resistant condenser has been developed. In order to verify the design it was needed to determine the maximum pressure inside the condenser during thawing. The pressure determination is performed by a dedicated test set-up with strain gauges.
The paper describes the test and the implications on the condenser design. After an introduction on AMS, a description of the test set-up is given, followed by details on the calibration of the pressure sensors. Subsequently the test and test results are described.
It is concluded that the pressure build up during thawing follows the CO2 melting line found in the CO2 3-phase diagram. Therefore the condenser maximum design pressure directly follows from this diagram when the maximum unloaded condenser temperature is known. From thermal analyses this temperature was found to be −5 ºC leading to a condenser maximum design pressur e of 300 MPa. The condenser, comprising small diameter Inconel 718 tubing attached to a grooved aluminium plate (din = 1.0mm, dout = 3.0mm) is shown -by accepted stress calculation methods- to withstand this pressure within applicable safety margins.
Authors
Citation
van Donk, G., Bsibsi, M., Pauw, A., and van Es, J., "Testing of a Freeze-proof Condenser for the Tracker Thermal Control System on AMS-02," SAE Technical Paper 2007-01-3238, 2007, https://doi.org/10.4271/2007-01-3238.Also In
References
- Woering (NLR) A.A. Pauw (NLR) A. de Vries (NLR) A.W.G. Delil (NLR) A.A.M. Verlaat (NIKHEF) B. Thermal Modeling Issues Concerning the Mechanically Pumped Two-Phase CO 2 Cooling for the Ams-2 Tracker SAE technical paper 2002-01-2466 , Int.Conf. On Environmental Systems San Antonio, TX, USA July 2002
- van Es J. van Donk G. Pauw A. Verlaat B. Rens C.A.M. Jaarsma J. Brouwer M.P.A.M. “AMS02 Tracker Thermal Control System (TTCS) design, model and breadboard results” 34th Int. Conf. on Environmental Systems Colorado Springs USA 2004
- Delil A.A.M. “Two-Phase Developments for the International Space Station ISS: - AMS-2 TTCS, a Mechanically Pumped Two-Phase CO2 Cooling Loop for the Alpha Magnetic Spectrometer Tracker Experiment - CIMEX-3, Versatile Two-Phase Loop for the Fluid Science Laboratory” 12th Int.Heat Pipe Conference Moscow, Russia May 2002
- Bibus Metals: Datasheet Inconel Alloy 718. W.Nr. 2.4668.
- Young Warren C. 1989 Roark's Formulas for Stress and Strain 6 McGraw Hill Book Company
- Broeren Robert L. Duschatko R. John International Space Station Alpha Design-To-Freeze Radiators SAE technical paper series 951652
- MIL-STD-1522A 1984 Standard General Requirements for Safe design and Operation of Pressurized Missile and Space Systems
- MIL-HDBK-340 1985 Application guidelines for MIL-STD-1540B; test requirements for space vehicles