This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Failure Criterion for Stretch Bendability of Advanced High Strength Steels
Technical Paper
2006-01-0349
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Studies in an Angular Stretch Bend Test (ASBT) have demonstrated that the failure location moves from the side wall to punch nose area. This occurs as the R/T ratio decreases below a certain limit and applies to most low carbon steels with the exception of Dual Phase (DP) steels. Such behavior in DP steels indicates that bending effects have a severe impact on the formability of DP materials. Therefore, the traditional criterion using the forming limit curve (FLC) is not suitable to assess the formability at punch radius areas for DP steels due in part to its uniqueness of unconventional microstructures. In this paper, a new failure criterion, ‘Bending-modified’ FLC (BFLC), is proposed by extending the traditional FLC using the “Stretch Bendability Index” (SBI) concept for the stretch bendability assessment. This newly proposed failure criterion is then applied to FEA simulations of an ASBT test for a dual phase steel and a significant improvement on failure height prediction was achieved.
Recommended Content
Technical Paper | Shear Fracture in Advanced High Strength Steels |
Technical Paper | Formability and Spring Back Characterization of Advanced High Strength Steel |
Technical Paper | Influence of AHSS Part Geometric Features on Crash Behavior |
Authors
Citation
Wu, J., Zhou, D., Zhang, L., Zhou, Y. et al., "A Failure Criterion for Stretch Bendability of Advanced High Strength Steels," SAE Technical Paper 2006-01-0349, 2006, https://doi.org/10.4271/2006-01-0349.Also In
References
- Keeler, S. P. Backhofen, W. A. “Plastic Instability and Fracture in Sheet Stretched Over Rigid Punches” ASM Transactions Quarterly 56 25 48 1964
- Goodwin, G. M. “Application of Strain Analysis to Sheet Metal Forming in the Press Shop” SAE paper 680093 1968
- Tharrett, M. R. Stoughton, T. B. “Stretch-Bend Forming Limits of 1008 AK Steel” SAE paper 2003-01-1157 2003
- Sadagopan S. Wong, C Huang, M. Yan, B. “Stretch Bendability of Advanced High Strength Steels” SAE paper 2003-01-1151 2003
- Leu, D. K. “A Simplified Approach for Evaluating Bendability and Springback in Plastic Bending of Anisotropic Sheet Metal” J. Materials Processing Technology 66 9 17 1997
- Chien, W. Y. Pan, J. Tang, S. C. “A Combined Necking and Shear Localization Analysis for Aluminum Sheets under Biaxial Stretching Conditions” Int. J. Plasticity 20 1953 1981 2004
- Kessler, L. Beier, Th. Werner, H. Horstkott, D. Dell, H. Gese, H. “Material Selection for an Ultra High Strength Steel Component Based on the Failure Criteria of CrachFEM” Numisheet 2005 A 492 499 2005
- Demeri, M. Y. “The Stretch-Bend Forming of Sheet Metal” J. Applied Metalworking 2 3 10 1981
- Keeler, S. P. Brazier W. G. “Relationship between Laboratory Material Characterization and Press Shop Formability” Proceedings of Microalloying 75 New York 517 582 1977
- Konieczny, A. A. “On Formability Assessment of the Automotive Dual Phase Steels” SAE paper 2001-01-3075 2001
- Marciniak, Z. Duncan, J. L. The Mechanics of Sheet Metal Forming Edward Arnold 1992
- Pickering, F.B. Proc. Int. Conf. on Toward Ductility and Toughness ISIJ and JIMn Tokyo 1971
- Formability Characterization of A New Generation of High-Strength Steels AISI/DOE Technology Roadmap Program 2003