This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Performance of Candidate Materials and Coatings for Thermal Management Systems for Proton Exchange Membrane Fuel Cells
Technical Paper
2006-01-0219
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Proton exchange membrane fuel cells (PEMFC) require heat exchangers, pumps, valves and water separation devices to provide the functions of thermal and water management in the fuel cell balance of plant. Heat exchangers having relatively large surface areas are needed to cool the fuel cell engine at the low temperature differentials existing between the coolant and ambient air. All of these components must be durable in the deionized water environment prevalent within the water management system of the fuel cell. At the same time, contaminant-free cooling circuits are needed to prevent degradation of the fuel cell itself. Consequently, stainless steel or other exotic materials are conservatively specified in the deionized water circuits of current designs of fuel cell vehicles and power modules. The substitution of heavy and costly stainless steel components by aluminum would greatly benefit the implementation of PEMFCs as a competitive alternative energy source for motor vehicles. The focus of this paper is on selection and performance of materials for PEMFC heat exchanger applications. Candidate materials including stainless steel and aluminum alloys were investigated with respect to ionic contaminant release into deionized water coolants under simulated immersion and condensing heat exchange conditions. The effects of material composition, as-manufactured condition (brazing process method) and surface treatment (passivation) were characterized. The performance of selected organic and modified sol-gel coatings on aluminum substrates is also described. The coatings offered significant protection against the deionized water environment. Finally, the results of metallurgical investigations conducted on prototype heat exchangers recovered from fuel cell service are reported.
Recommended Content
Authors
Citation
Dionne, S., Zheng, W., Cheadle, B., and Liang, F., "Performance of Candidate Materials and Coatings for Thermal Management Systems for Proton Exchange Membrane Fuel Cells," SAE Technical Paper 2006-01-0219, 2006, https://doi.org/10.4271/2006-01-0219.Also In
References
- Ralph T. R. Hards G. A. “Fuel cells: clean energy production for the new millennium” Chemistry and Industry 9 5 1998 334 335
- Oei D.G. “Direct hydrogen-fueled proton-exchange-membrane (PEM) fuel cell for transportation” Proceedings of the 1995 SAE Alternative Fuels Conference, Technical Paper 952763 Warrendale, PA SAE 1995 229 234
- Srinivasan S. et al. “Proton exchange membrane fuel cells for space and electric vehicle applications: From basic research to technology development” Dual-Use Space Technology Transfer Conference and Exhibition Houston, TX NASA 1994 409 420
- Fronk M. H. et al. “PEM Fuel Cell Systems Solutions for Transportation” Fuel Cell Power for Transportation 2000 (SP-1505), Technical Paper 2000-01-0373 Warrendale, PA SAE 2000
- Oei D. G. et al. “Direct-hydrogen-fueled proton-exchange-membrane fuel cell system for transportation applications” Washington, DC 1997
- Srinivasan S. et al. “Progress in proton exchange membrane fuel cell technology at Texas A and M University” Proc. of the 28th intersociety energy conversion engineering conference 1 Aerospace power, conversion technology, electrochemical conversion Washington, DC American Chemical Society 1993 1.1195 1.1201
- Mueller S. A. et al. “Leaching of Ions from Fuel Cell Vehicle cooling System and their Removal to Maintain Low Conductivity” Warrendale, PA SAE International 2003
- Binger W. W. Marstiller C. M. “Aluminum Alloys for Handling High-purity Water” Corrosion 13 9 1957 591 596
- ASTM Designation A380 “Standard Practice for Cleaning and Descaling Stainless Steel Parts, Equipment, and Systems” Philadelphia, USA American Society for Testing of Materials
- Field D. J. Steward N. I. “Mechanistic aspects of the Nocolok flux brazing process” SAE Paper No. 870186 , (presented at SAE Intl Congress and Expo Detroit MI Feb 23-27 1987 1 11
- Hawksworth D. K. Scholin K. Woods R. “Tube/fin fillet formation in CAB brazed Condensers” VTMS-6 2003 401
- Cheadle B. E. Dockus K. F. “Inert Atmosphere Fluxless Brazing of Aluminum Heat Exchangers” SAE Paper No. 880446 , (presented at SAE Intl Congress and Expo Detroit MI Feb 29 Mar 04 1988 1 11
- Cortese M. James R. “A Study of Material Compatibility with Deionized Water” Warrendale, PA SAE International 2003
- Dionne S. et al. “Contaminant Release and Degradation of Heat Exchanger Materials in a Deionized Water Coolant for Use in Proton Exchange Membrane Fuel Cell Systems” Proceedings of Materials Science and Technology 2005 Conference Pittsburg, IL Sept. 25-28 2005
- Fujiwara K. et al. “Effect of Surface-Oxidation Conditions on Metal Release for Stainless Steel in High-Temperature Pure Water” Corrosion Engineering 36 6 1987 343 350
- Wernick S. Pinner R. Sheasby P. G. “The Surface Treatment and Finishing of Aluminum and its Alloys” 2 5th ASM International and Finishing Publications 1987
- Aluminum and Aluminum Alloys ASM Specialty Handbook Materials Park OH ASM International 1993 609 610
- Krenz F. H. “Corrosion of Aluminum-Nickel Type Alloys In High Temperature Aqueous Service” Corrosion 13 9 1957 575 581
- Draley J. E. Ruther W. E. “Aqueous Corrosion of Aluminum Part 2 - Methods of Protection Above 200C” Corrosion 12 10 1956 480 490