This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Recommended Practice for Dynamic Testing for Sheet Steels - Development and Round Robin Tests
Technical Paper
2006-01-0120
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Tensile properties of sheet steels at dynamic conditions are becoming more important for automotives in recent years due to the positive strain rate effect of steels which significantly improves energy absorption capability during crash events. However, several testing techniques are used by different testing laboratories, no testing standards are available, and the quality of data generated by different laboratories is often not comparable. In order to improve the data quality at high strain rate testing conditions and thus to improve the accuracy of crash simulation results, The International Iron and Steel Institute (IISI) initiated a project to develop the “Recommendations for Dynamic Tensile Testing of Sheet Steels”. The document provides guidelines for key elements of high strain rate testing, testing techniques, input methods, specimen geometry and stress/strain measurement instrumentations. A Round Robin test program was launched afterwards to evaluate the current status of testing quality with 10 laboratories participating from Europe, Japan, Korea and North America. The Round Robin test program showed that not only the equipment used are different, specimen dimensions are also vastly different from different testing laboratories. This paper describes the development of the document, key issues of the high strain rate testing, and Round Robin test results. An example is also given showing how data quality was significantly improved by careful refinement of the testing procedures including specimen geometry.
Recommended Content
| Technical Paper | Coating Formability Evaluation Method for Hot-Dip Galvannealed Sheet |
| Journal Article | Forming Limit Diagrams of Ground St14 Steel Sheets with Different Thicknesses |
| Technical Paper | Galvanic Corrosion Prevention of Steel-Aluminum Couples |
Authors
Citation
Yan, B., Kuriyama, Y., Uenishi, A., Cornette, D. et al., "Recommended Practice for Dynamic Testing for Sheet Steels - Development and Round Robin Tests," SAE Technical Paper 2006-01-0120, 2006, https://doi.org/10.4271/2006-01-0120.Also In
Modeling Testing & Design of Materials Dummies & Structures for Crash Safety Applications
Number: SP-2037; Published: 2006-04-03
Number: SP-2037; Published: 2006-04-03
References
- “Strain Rate Dependent Material Properties in CAE Analysis for Crashworthiness” Porsche Engineering Service, Inc. report to ULSAB-AVC Consortium 2000
- Recommended Practice for Dynamic Tensile Test for Sheet Steels” IISI High Strain Rate Experts Team 2005
- Hopkinson B. “A Method of Measuring the Pressure Produced in the Detonation of Explosives or by the Impact of Bullets” Phil. Trans. A 213 1914 437
- Davies R. M. “A Critical Study of the Hopkinson Pressure Bar” Phil. Trans. A 240 1948 375
- Kolsky H. “An Invistigation of the Mechanical Properties of Materials at Very High Rates of Loading” Proc. Royal Soc. B 62 1949 676
- Kawata et al. “On High-velocity Brittleness and Ductility of Dual Phase Steel and Some Hybrid Fiber reinforced Plastics”, in “Recent Advances in composites in the United States and Japan” ASTM STP 864 Am. Soc. For Testing and Materials Philadelphia 1985 700
- Gama B. A. Lopatnikov S. L. Gillespie J. W., Jr. “Hopkinson Bar Experimental Technique: A Critical Review” Appl Mech Rev 57 4 July 2004 223 250
- Yan B. Xu K. “High Strain Rate Behavior Of Advanced High Strength Steels For Automotive Applications” 44 th Mechanical Working and Steel Processing Conference Proceedings XL 2002 493 509
- Tanimura S. Mimura K. “Impact Engineering and Application Chiba A. Tanimura S. Hokamoto K. Elsevier Science 57 64 2001
- Wong C. “IISI-AutoCo Round-Robin Dynamic Tensile Testing Project” IISI June 2005
- Bruce D. M. Matlock D.K. Speer J. G. De A.K. “Assessment of the Strain-Rate Dependent Tensile Properties of Automotive Sheet Steels” SAE Warrendale, PA 2004