This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Improved Pneumatic Aerodynamics for Drag Reduction, Fuel Economy, Safety and Stability Increase for Heavy Vehicles
Technical Paper
2005-01-3627
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Aerodynamic drag is the major component of Heavy Vehicle (HV) resistance at typical highway speeds, and thus strongly impacts related fuel economy because horsepower required to overcome this drag increases as the cube of vehicle speed. In an ongoing drag-reduction program for HVs conducted for the US Department of Energy (DOE), Georgia Tech Research Institute (GTRI) has been applying advanced new aerodynamic technology previously developed for aircraft. This technology uses tangential blowing to reduce the drag generated by these bluff-based high-drag vehicles, particularly the trailer. Drag reduction can be accomplished by this blown concept without moving surfaces, and it also offers the potential to increase drag for braking if needed and to overcome both increasing drag and destabilizing side forces due to large side winds and gusts. Wind-tunnel evaluations of baseline unmodified HVs and of the latest blown Pneumatic Heavy Vehicle (PHV) configurations have confirmed drag coefficient reductions of up to 31% below the baseline due to these new pneumatic configuration improvements. These tunnel results have led to a recent full-scale on-track SAE Type-II fuel economy evaluation of this concept installed on a Volvo-Great Dane test vehicle combo. Test-track results have shown an 11-12% Fuel Economy Increase (FEI) for this blown vehicle, which is reduced somewhat to 8-9% FEI once the fuel to drive the proof-of-concept onboard test blowers is included. Since 1% FEI represents approximately 200 million gallons of diesel fuel saved if employed by the entire US HV fleet, optimistic promise is shown by this data. These model- scale and full-scale results are presented in this paper, as are experimental results showing aerodynamic braking and side-wind control resulting from slight modifications to the blown system applied to advanced PHV configurations.
Recommended Content
Authors
Citation
Englar, R., "Improved Pneumatic Aerodynamics for Drag Reduction, Fuel Economy, Safety and Stability Increase for Heavy Vehicles," SAE Technical Paper 2005-01-3627, 2005, https://doi.org/10.4271/2005-01-3627.Also In
Heavy Vehicle Drag Reduction-Overviews, Multiple Trailer-Mounted Devices; Tires, Splash and Spray and Emissions; Full Scale Assessments
Number: SP-1985; Published: 2005-11-01
Number: SP-1985; Published: 2005-11-01
References
- Englar, Robert J. “Circulation Control Pneumatic Aerodynamics: Blown Force and Moment Augmentation and Modification; Past, Present and Future,” AIAA Paper 2000-2541 Denver, CO June 19-22 2000
- Englar, Robert J. “Advanced Aerodynamic Devices to Improve the Performance, Economics, Handling and Safety of Heavy Vehicles,” SAE Paper 2001-01-2072 Washington, DC May 14-16 2001
- Englar, R. J. “Pneumatic Heavy Vehicle Aerodynamic Drag Reduction, Safety Enhancement, and Performance Improvement,” Proceedings of the UEF Conference on “The Aerodynamics of Heavy Vehicles: Trucks, Buses, and Trains” Pacific- Grove, CA Dec. 2-6 2002
- Englar, Robert J. “Drag Reduction, Safety Enhancement and Performance Improvement for Heavy Vehicles and SUVs Using Advanced Pneumatic Aerodynamic Technology” SAE Paper 2003-01-3378 Ft. Worth Nov. 10-12 2003
- Diamond, Sidney “FY2003 Annual Progress Report for Heavy Vehicle Systems Optimization, FreedomCAR and Vehicle Technologies Program” February 2004
- Englar, R. J. “Continued Development & Improvement of Pneumatic Heavy Vehicles, Phase VI, DOE Quarterly Report 7,” April 15 2004
- Englar, R. J. “Continued Development & Improvement of Pneumatic Heavy Vehicles, Phase VI, DOE Quarterly Report. 8,” July 15 2004
- “Joint TMC/SAE Fuel Consumption Test Procedure-Type-II,” SAE J1321 Oct. 1986
- Jones, G. S. Englar R. J. “Advances in Pneumatic-Controlled High-Lift Systems Through Pulsed Blowing” AIAA 2003-3411, AIAA 21 st Applied Aerodynamics Conference Orlando June 23-26 2003