This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
NVH Experiments and Analyses for an Single Cylinder Engine Model Assembled with Tap-Bolts and with Through-Bolts
Technical Paper
2005-01-2531
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A series of NVH experiments were performed for a set of single cylinder engine models made of aluminum, with bore sizes of 100mm. Each engine model consists of a cylinder head, a cylinder block and a bedplate. Each has the same size of 150mm × 150mm, with different heights of 100mm, 200mm and 80mm, respectively. By choosing 112 measuring points on the structure surfaces, we performed a series of impact tests for the following cases,
- (a)The cylinder head and the bedplate were fastened to the cylinder block by two sets of ISO M10 Tap-bolts, each with the lengths l1=117mm and l2=97mm.
- (b)The cylinder head and the bedplate were fastened to the cylinder block together by a set of ISO M10 Through-bolts of grip length l3=380mm.
From a series of acceleration measurements, it was found that
- (1)Significantly dominant bending nodes are induced in the X-Y plane, which is vertical to the crankshaft center line.
- (2)13 of the resonance peaks appeared in the frequency range below 7000 Hz for the case (a), whereas only 6 for the case (b).
- (3)Compared to the 3143Hz of the lowest fundamental natural frequency for the case (a), a higher value of 3450Hz appeared for the case (b).
- (4)Significant reduction of the engine model surface vibration is caused for the case (b).
To investigate the reasons of such differences, the engine structure model was idealized as a set of beam elements consisting of variable cross-sections, to calculate the fundamental natural frequency, by Rayleigh's method. By applying 38 beam elements, and 3 sets of bolt joints each consisting of bolt and clamped member, we could calculate the fundamental natural frequencies successfully. Finally, we found that the higher natural frequencies and excellent NVH characteristics are caused by the larger values of flexural rigidity for the case (b).
Recommended Content
Technical Paper | NVH Experimental Analyses for an Engine Structure Model Assembled with Ordinary Tap Bolts and with Through Bolts |
Technical Paper | Valve Problems with Lead Free Gasoline |
Technical Paper | Predictive Engine Spark Timing Control |
Authors
Citation
Okamura, H., Yamashita, K., Shimizu, S., and Sakamoto, H., "NVH Experiments and Analyses for an Single Cylinder Engine Model Assembled with Tap-Bolts and with Through-Bolts," SAE Technical Paper 2005-01-2531, 2005, https://doi.org/10.4271/2005-01-2531.Also In
References
- Gomes Enio Breida Mary Kley Philipp Ratliff Mark “NVH Optimization of 1.2L DIATA Engine,” SAE Paper 1999-01-1744
- Schoffmann Wolfgang Beste Frank Atzwanger Martin Marquard Ralf “Lightweight Engine Structure-Crankcase Concept for High-Performance Diesel Engine” Auto Technology October 2002 2 50 53
- Uematsu Yutaka Nakada Teruo Zhang Long Ichikawa Hiroyuki Haverdink William H. “High Fuel Economy CIDI Engine for GM PNGV Program,” SAE Paper 2002-01-1084
- Yamashita Kenichi Okamura Hideo et al. “NVH Experimental Analyses for an Engine Structure Model Assembled with Ordinary Tap Bolts and with Through Bolts,” SAE Paper 2003-01-1732
- Thomason W.T. “Mechanical Vibration,” 2nd Prentice hall 1963
- Den Hartog J. P. “Mechanical Vibrations,” 4th McGraw-Hill Book Company 1956 155
- Juvinall R.C. Marshek K.M. “Fundamentals of Machine Component Design,” 2nd John Wiley & Sons 1993
- Shigley J.E. Mischke C.R. “Mechanical Engineering Design,” 5th McGraw-Hill Book Company 1989