This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Effects of Roller Geometry on Contact Pressure and Residual Stress in Crankshaft Fillet Rolling
Technical Paper
2005-01-1908
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
In this paper, the effects of roller geometry on contact pressure and residual stress in crankshaft fillet rolling are investigated by a two-dimensional finite element analysis. The fillet rolling process is first introduced to review some characteristics of the rolling tools. A two-dimensional plane strain finite element analysis is then employed to qualitatively investigate the influence of the roller geometry. Computations have been conducted for eight different contact geometries between the primary roller and the secondary roller to investigate the geometry effect on the contact pressure distribution on the edge of the primary roller. Fatigue parameters of the primary rollers are also estimated based on the Findley fatigue theory. Then, computations have been conducted for three different contact geometries between the primary roller and the crankshaft fillet to investigate the geometry effect on the residual stress distribution near the crankshaft fillet. The results suggest that the contact geometry between the two rollers has significant influence on the contact pressure distribution and the maximum contact pressure along the edge of the primary roller and, consequently, the fatigue lives of the primary rollers. The results also suggest that the contact geometry between the primary roller and the crankshaft fillet does not have significant influence on the overall residual stress distribution and, consequently, may not have significant influence on the fatigue performance of crankshaft sections under bending loads. Therefore, an appropriate adjustment of the contact geometry between the two rollers can significantly improve the fatigue lives of the primary rollers without a significant change of the overall residual stress distributions near the crankshaft fillet and, in turn, the fatigue performance of crankshaft sections under bending loads.
Recommended Content
Authors
Citation
Choi, K., Pan, J., and Ho, S., "Effects of Roller Geometry on Contact Pressure and Residual Stress in Crankshaft Fillet Rolling," SAE Technical Paper 2005-01-1908, 2005, https://doi.org/10.4271/2005-01-1908.Also In
References
- Love, R. J. Waistall, D. N. 1954 The improvement in the bending fatigue strength of production crankshafts by cold rolling M.I.R.A. Report No. 1954/1 1 8
- Bhargava, V. Hahn, G. T. Rubin, C. A. 1985 An elastic-plastic finite element model of rolling contact - part 1: analysis of single contacts J. Appl. Mech. Transactions of the ASME 52 67 74
- Bhargava, V. Hahn, G. T. Rubin, C. A. 1985 An elastic-plastic finite element model of rolling contact - part 2: analysis of repeated contacts J. Appl. Mech. Transactions of the ASME 52 75 82
- Yu, M. Moran, B. Keer, L. M. 1993 A direct analysis of two-dimensional elastic-plastic rolling contact J. Tribology Transactions of the ASME 115 227 236
- Bijak-żochowski, M. Marek, P. 1997 Residual stress in some elasto-plastic problems of rolling contact with friction Int. J. Mech. Sci. 39 15 32
- Jiang, Y. Sehitoglu, H. 1999 A model for rolling contact failure Wear 224 38 49
- Ringsberg, J. W. 2001 Life prediction of rolling contact fatigue crank initiation Int. J. Fatigue 23 575 586
- Ahmadi, N. Keer, L. M. Mura, T. 1983 Non-Hertzian contact stress analysis for an elastic half space - normal and sliding contact Int. J. Solids Struct. 19 357 373
- Ju, S. H. Horng, T. L. Cha, K. C. 2000 Comparisons of contact pressures of crowned rollers J. Engng. Tribology Proceedings of the Institution of Mechanical Engineers 214 147 156
- Poplawski, J. V. Peters, S. M. Zaretsky, E. V. 2001 Effect of roller profile on cylindrical roller bearing life prediction - part II comparison of roller profiles Tribology Trans. 44 417 427
- Goryacheva, I. G. Murthy, H. Farris, T. N. 2002 Contact problem with partial slip for the inclined punch with rounded edges Int. J. Fatigue 24 1191 1201
- Choi, K. S. Pan, J. Ho, S. 2004 Fatigue failure of rollers in crankshaft fillet rolling SAE Paper 2004-01-1498 Society of Automotive Engineers Warrendale, PA
- Chien, W. Y. Pan, J. Close, D. Ho, S. 2005 Fatigue analysis of crankshaft sections under bending with consideration of residual stresses Int. J. Fatigue 27 1 19
- Trojahn, W. Streit, E. Chin, H. Ehlert, D. 1998 Progress in bearing performance of advanced nitrogen alloyed stainless steel Bearing steels: into the 21st century Hoo J. J. C. Green W. B. American Society for Testing and Materials West Conshohocken, PA
- Hibbitt, H. D. Karlsson, B. I. Sorensen, E. P. 2001 ABAQUS user manual
- Tartaglia, J. M. Ritter, P. E. Gundlach, R. B. Jenkins, L. 2000 Monotonic and cyclic property design data for ductile iron castings SAE Paper 2000-01-0758 Society of Automotive Engineers Warrendale, PA
- Findley, W. N. Coleman, J. J. Hanley, B. C. 1956 Theory for combined bending and torsion fatigue with data for SAE 4340 steel Proceedings of the International Conference on Fatigue of Metals Institution of Mechanical Engineers 150 156
- Findley, W. N. 1959 A theory for the effect of mean stress on fatigue of metals under combined torsion and axial load or bending J. Engng. Industry Transactions of the ASME 81 301 306