This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Study of the Influence of Geometrical and Injection Parameters on Diesel Sprays Characteristics in Isothermal Conditions
Technical Paper
2005-01-0913
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This paper deals with the problem of quantifying and predicting the macroscopic spray behaviour as a function of the parameters governing the injection process. The parameters studied were ambient gas density as a representative parameter external to the system, and nozzle hole diameter and injection pressure as influential system parameters.
The main purpose of this research is to validate and extend the different correlations available in the literature to the actual Diesel engine conditions, i.e. high injection pressure, small nozzle holes, severe cavitating conditions, etc.
The sprays from five axi-symmetrical nozzles with different diameters are characterized in two different test rigs that can reproduce the real engine in-cylinder air density and pressure.
The wide parametric study that was performed has permitted to quantify the effects of the injection pressure, nozzle hole diameter and environment gas density on the spray tip penetration. The experimental results obtained from both test rigs have shown good agreement with the theoretical analysis. However, when compared between themselves, there have been observed small but consistent differences between the two test rigs, from the spray penetration and cone angle viewpoint.
Recommended Content
Authors
- J. M. Desantes - CMT-Motores Térmicos. Universidad Politécnica de Valencia, Spain
- R. Payri - CMT-Motores Térmicos. Universidad Politécnica de Valencia, Spain
- F. J. Salvador - CMT-Motores Térmicos. Universidad Politécnica de Valencia, Spain
- V. Soare - CMT-Motores Térmicos. Universidad Politécnica de Valencia, Spain
Citation
Desantes, J., Payri, R., Salvador, F., and Soare, V., "Study of the Influence of Geometrical and Injection Parameters on Diesel Sprays Characteristics in Isothermal Conditions," SAE Technical Paper 2005-01-0913, 2005, https://doi.org/10.4271/2005-01-0913.Also In
References
- Hay, N. Jones, P.L. “Comparison of the various correlations for spray penetration” SAE Paper 720776 1972
- Dent, J.C. “A basis for the comparison of various experimental methods for studying spray penetration” SAE Paper 710571 1971
- Wakuri, Y. Fujii, M. Amitani, T. Tsuneya, R. “Studies of the penetration of a fuel spray in a Diesel engine” Bull. J.S.M.E. 3 9 123 130 1960
- Hiroyasu, H. Arai, M. “Structures of fuel sprays in Diesel engines” SAE Paper 900475 1990
- Desantes JM Payri R Salvador FJ Gimeno J. “Measurements of spray momentum for the study of cavitation in diesel injection nozzles” SAE Paper 2003-01-0703 2003
- Payri, R. García, J.M. Salvador, F.J. Gimeno J. “Using spray momentum flux measurements to understand the influence of Diesel nozzle geometry on spray characteristics” Fuel In Press
- Pastor, J.V Payri, R. López, J.J. Juliá, J.E. “Effect of injector nozzle geometry of Diesel engines on the macroscopic spray characteristics by means of optical techniques” Fuel injection systems. ImechE conference transactions 2003 73 82
- Pastor, J.V. Arrègle, J. Palomares, A. “Diesel spray image segmentation with a likelihood ratio test” Applied Optics 40 17 2876 2885 2001
- Arai, M. Shimizu, M. Hiroyasu, H. “Similarity between the break-up lengths of a high speed liquid jet in atmospheric and pressurized conditions” In ICLASS-91 Gaithersburg, Maryland 1991
- Hurly, J.J. Defibaugh, D.R. Moldover, M.R. “Thermodynamic properties of SF 6 ” Int. J. Thermophysics 2000 21 739 765
- Macián, V. Bermúdez, V. Payri, R. Gimeno, J. “New technique for the determination of the internal geometry of Diesel nozzle with the use of the silicone methodology” Exp. Tech 2003 27 2 39 43
- Payri R Margot X Salvador FJ. “A Numerical Study of the Influence of Diesel Nozzle Geometry on the Inner Cavitating Flow” SAE Paper 2002-01-215 2002
- Macián V. Payri R. Margot X. Salvador F.J. “A CFD Analysis of the Influence of Diesel Nozzle Geometry on the inception of Cavitation” Atom Sprays 2003 13 579 604
- Payri F. Bermúdez V. Payri R. Salvador F.J. “The influence of cavitation on the internal flow and the Spray characteristics in diesel injection nozzles” Fuel 2004 83 419 31
- Payri, R. Molina, S. Salvador, F.J. Gimeno, J. “A study of the relation between nozzle geometry, internal flow and sprays characteristics in Diesel Fuel injection systems” KSME International Journal 18 7 1222 1235 2004
- Payri, R. Guardiola, C. Salvador, F.J. Gimeno, J. “Critical cavitation number determination in Diesel injection nozzles” Experimental techniques 28 3 49 51 2004
- Desantes, J.M. Payri, R. Pastor, J.M. Gimeno, J. “Experimental Analysis of Fuel Evaporation in Diesel Sprays. Part I. Nozzle characterization” Atomization and Sprays 2005
- Cheong, S.-K. Liu, J. Shu, D. Wang, J. Powell, C.F. “Effects of ambient pressure on dynamics of near-nozzle Diesel sprays studied by ultrafast X-Radiography” SAE Paper 2004-01-2026 2004
- MacPhee, A.G. Tate, M.W. Powell, C.F. Yue, Y. Renzi, M.J. et al. “X-ray imaging of shock waves generated by high-pressure fuel sprays” Science 295 1261 1263 2002
- Payri, R. Climent, H. Salvador, F.J. Favennec, A.G. “Diesel injection system modelling. Methodology and application for a first-generation common rail system” Proc. Instn. Mech. Engrs. 218 Part D: Automobile Engineering 81 91
- Bosch, W. “The fuel rate indicator: A new measuring instrument for display of the characteristics of individual injection” SAE Paper 660749 1966
- Arrègle, J. Pastor, J.V. Ruiz, S. “The influence of injection parameters on Diesel Spray characteristics” SAE Paper 1999-01-0200 1999
- Naber, J. Siebers, D.L. “Effects of gas density and vaporisation on penetration and dispersion of Diesel sprays” SAE Paper 960034 1996
- Payri, F. Desantes, J.M. Arrègle, J. “Characterization of D.I. Diesel sprays in high density conditions” SAE Paper 960774 1996