This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Development of the Enhanced Vehicle and Engine Cooling System Simulation and Application to Active Cooling Control
Technical Paper
2005-01-0697
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The increasing complexity of vehicle engine cooling systems results in additional system interactions. Design and evaluation of such systems and related interactions requires a fully coupled detailed engine and cooling system model. The Vehicle Engine Cooling System Simulation (VECSS) developed at Michigan Technological University was enhanced by linking with GT-POWER for the engine/cycle analysis model. Enhanced VECSS (E-VECSS) predicts the effects of cooling system performance on engine performance including accessory power and fuel conversion efficiency. Along with the engine cycle, modeled components include the engine manifolds, turbocharger, radiator, charge-air-cooler, engine oil circuit, oil cooler, cab heater, coolant pump, thermostat, and fan. This tool was then applied to develop and simulate an actively controlled electric cooling system for a 12.7 liter diesel engine.
Recommended Content
Authors
Citation
Luptowski, B., Arici, O., Johnson, J., and Parker, G., "Development of the Enhanced Vehicle and Engine Cooling System Simulation and Application to Active Cooling Control," SAE Technical Paper 2005-01-0697, 2005, https://doi.org/10.4271/2005-01-0697.Also In
References
- Chalgren, R.D. “The Modeling of Exhaust Gas Recirculation in the Vehicle Engine Cooling System Simulation For Designing a Controlled EGR Cooling System,” Michigan Technological University 2000
- Cortona, E.K. “Engine Thermomanagement for Fuel Consumption Reduction” Doctor of Technical Sciences Dissertation Swiss Federal Institute of Technology Zurich 2000
- Cortona, E. Onder, C.H. “Engine Thermal Management with Electric Cooling Pump,” SAE Paper 2000-01-0965 2000
- Mohan K.V. Arici O. Yang S. Johnson J. “A Computer Simulation of the Turbocharged Diesel engine as an Enhancement to the Vehicle Engine Cooling System Simulation” SAE Paper 971804
- Luptowski, B.J. “Development and Evaluation of an All Electric Active Cooling System in a Heavy Duty Diesel Truck Using the Vehicle Engine Cooling System Simulation Enhanced with GT-POWER” Michigan Technological University 2003
- 1996 ASHRAE Systems and Equipment Handbook (SI)
- Ozisik, M.N. Heat Transfer: a basic approach McGraw-Hill New York, NY 1985
- Burden, R.L. Faires, J.D. Numerical Analysis PWS Publishers Boston, MA 1985
- Salvonen, C.L. “Modeling of Thermal Characteristics of Oil and Coolant Flows Within a Diesel Engine Cooling System and a Parametric Study of Variables Influencing its Performance” Michigan Technological University 1984
- Arici, O. Johnson, J. Kulkarni, A.J. “The Vehicle Engine Cooling System Simulation Part 1-Model Development” SAE Paper 199-01-0240
- Ursini, V.J. “A Computer Simulation Program for Evaluation of the Cooling System Performance of a Diesel Powered Truck,” Michigan Technological University 1982
- Hong, T. Rakotovao, M. Henner, M. Moreau, S. Savage, J. “Thermal Analysis of Electric Motors in Engine Cooling Fan Systems,” SAE Paper 2001-01-17 2001
- Brace, C.J. Burnham-Slipper, H. Wijetunge, R.S. Vaughan, N.D. Wright, K. Blight, D. “Integrated Cooling Systems for Passenger Vehicles,” SAE paper 2001-01-1248 2001
- Robert Bosch Corporation 2002
- Assanis D.N. Heywood, J.B. “Development and Use of a Computer Simulation of the Turbocompounded Diesel System for Engine Performance and Component Heat Transfer Studies,” SAE Paper 860329 1986
- Pischinger, R. “The Importance of Heat Transfer to IC Engine Design and Operation,” Heat and Mass transfer in gasoline and Diesel Engines New York, NY Hemisphere Publishing Corporation 1989
- Woschni, G. “Experimental Investigation of the Heat Transfer in Internal Combustion Engines with Insulated Combustion Chamber Walls,” Heat and Mass transfer in gasoline and Diesel Engines New York, NY Hemisphere Publishing Corporation 1989
- Morel, T. Fort, E.F. Blumberg, P.N. “Effect of Insulation Strategy and Design Parameters on Diesel Engine Heat Rejection and Performance,” SAE Paper 850506 1985
- Suryanarayana, N.V. Engineering Heat Transfer West Publishing Company St. Paul, MN 1994
- Krause, W. Spies, K.H. “Dynamic Control of the Coolant Temperature for a Reduction of Fuel Consumption and Hydrocarbon Emission,” SAE Paper 960271
- Jarrier, L. Champoussin J.C. Yu. R. Gentile D. “Warm-Up of a D.I. Diesel Engine: Experiment and Modeling” SAE Paper 2000-01-0299 2000
- Koch, F.W. Haubner F.G. “Cooling System Development and Optimization for DI Engines” SAE Paper 2000-01-0283 2000
- Heywood, J.B. Internal Combustion Engine Fundamentals McGraw-Hill 1988
- Fellague, K.A. Hu, S. Willaughby, D.A. “Determination of the Effects of Inlet Air Velocity and Temperature Distributions on the Performance of an Automotive Radiator,” SAE Paper 940771 1994
- Lehner, C. Parker, G. Arici, O. Johnson, J. “Design and Development of a Model Based Feedback Controlled Cooling System for Heavy Duty Diesel Truck Applications Using a Vehicle Engine Cooling System Simulation” SAE Paper 2001-01-0336
- Smith O.J.M. “A Controller to Overcome Dead Time,” ISA Journal 6 2 28 33 1959