This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A New GDI 2-Stroke Engine to Meet Future Emission Limits: The Design and Prototype Architecture
Technical Paper
2004-32-0041
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
As more stringent emission limits and low consumption requirements also involve s.i. 2-stroke engines, one of the most important design modifications that can cope with these constraints is to perform the scavenging process using pure air, which means not only fuel-free air but also oil-free air. A new single-cylinder prototype engine, equipped with a gasoline direct injection (GDI) apparatus has therefore been designed and built. In order to reduce manufacturing costs, this prototype was obtained by modifying a mass-produced 4-stroke 4-cylinder automotive engine. Apart from the replacement of the original indirect fuel feeding system with GDI, two more remarkable features should be pointed out: the use of a force-fed lubrication system, like those used in current 4-stroke engines and, as a consequence, the use of an external scavenging pump.
Before using an electronically controlled direct injection system on the new prototype engine, the whole apparatus was tested on a mass-produced crankcase scavenged 2-stroke engine (Husqvarna WR 250) in order to evaluate the magnitude of the improvements. A comparison of a carburettor fuel feeding system with a direct fuel injection system was carried out, under cubic power requirements, to check whether the GDI strategies were advantageous. As satisfying results were obtained, the direct injection apparatus was mounted onto the prototype engine for the first experimental tests.
Recommended Content
Authors
Topic
Citation
Antonelli, E., Nuccio, P., Dongiovanni, C., and Marzano, M., "A New GDI 2-Stroke Engine to Meet Future Emission Limits: The Design and Prototype Architecture," SAE Technical Paper 2004-32-0041, 2004, https://doi.org/10.4271/2004-32-0041.Also In
References
- Goggi A. “Un nuovo motore a due tempi ad accensione comandata ad alte prestazioni” 1987-88
- Rochelle P. “Emission and Fuel Consumption Reduction in a Two-Stroke Engine Using Delay-Charging” SAE Paper N. 951784
- Gesmundo A. “Messa a punto di un nuovo motore a due tempi ad accensione comandata” 1989-90
- Katsuo et al. “Combustion Control Technologies of Mitsubishi Direct Injection SI Engine” International SAE Congress Detroit 26-29 February 1996 SAE Paper N. 960600
- Takagi Y. et al. “Simultaneous Attainment of Low Fuel Consumption, High Output Power and Low Exhaust Emissions in Direct Injection SI Engines” SAE Paper N. 980149
- Noma K. et al. “Gasoline Direct Injection Engine for the European Market” SAE Paper N. 980150
- Kano M. et al. “Analysis of Mixture Formation of Direct Injection Gasoline Engine” SAE Paper N. 980157
- Kuwahara K. et al. “Control Strategy for Engine Performance Improvement in a Gasoline Direct Injection Engine” SAE Paper N. 980158
- Bell G. Finucci C. “Exhaust Emission Sensitivities with Direct Injection on a 50 cc Scooter” SAE Paper N. 970365
- Murayama T. et al. “Study on Exhaust Control Valves and Direct Air-Fuel Injection for Improving Scavenging Process in two-Stroke Gasoline Engines” SAE Paper N. 960367
- Bombelli A. “Applicazione dell'iniezione diretta di combustibile in motori a due tempi ad accensione comandata” 1999-00
- Lanfranchini S. “Progettazione e sperimentazio-ne di un motore a due tempi ad accensione comandata di nuova concezione” 2000-01
- Grieco F. “Verifica sperimentale delle prestazioni di un motore a due tempi ad iniezione diretta di benzina” 2001-02
- Crescenzi M. “Progettazione di un motore a due tempi ad accensione comandata di tipo innovativo” 2001-02
- Camoriano M. “Motore a due tempi ad accensione comandata per uso automobilistico” 1993-94
- Bersia M. “Progetto e realizzazione di un prototipo monocilindrico a due tempi di tipo innovativo” 1995-96
- Seresin A. “Motore a 2 tempi di nuova concezione: studio e realizzazione del sistema di iniezione e dell'apparato di alimentazione” 1998-99
- Allari S. “Realizzazione di un monocilindrico a due tempi di nuova concezione: problemi relativi alla legge di alzata delle valvole” 1997-98
- Germano G. “Realizzazione di un monocilindro a due tempi di nuova concezione: problemi relativi alla distribuzione e all'azionamento della pompa di lavaggio” 1997-98
- De Nicola L. “Motore a due tempi di nuova concezione: progettazione degli apparati di alimentazione e accensione” 1998-99
- Medina F. “Realizzazione di un motore alternativo a due tempi a ciclo Otto di tipo innovativo” 1998-99
- Amadio V. “Applicazione dell'Iniezione Diretta di Benzina in un Motore a 2 Tempi di Tipo Innovativo” 2002-03
- Miyamoto T. et al. “Structure of Spray from an Air Assist Hollow-Cone Injector” SAE Paper N. 960771
- Kenny R.G. Kee R.J. Carson C.E. Blair G.P. “Application of Direct Air-Assisted Fuel Injection to an S.I. Cross-Scavenged Two-Stroke Engine” SAE Paper N. 932396
- Marini A. Gentili R. “Sistema PRO-JECT di Iniezione Pneumatica per Motori a Due Tempi ad A.C.” 50° Congresso Nazionale ATI 12-15 Sett. 1995