This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Plastic Waste Processing and Volume Reduction for Resource Recovery and Storage in Space
Technical Paper
2003-01-2369
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This paper describes work that has begun at Ames Research Center on development of a heat melt compactor that can be used on near term and future missions. The heat melt compactor can handle wastes with a significant plastic composition and minimize crew interaction.
The current solid waste management system employed on the International Space Station (ISS) consists of compaction, storage, and disposal. Wastes such as plastic food packaging and trash are compacted manually and wrapped in duct taped “footballs” by the astronauts. Much of the waste is simply loaded into the empty Russian Progress spacecraft that is used to bring supplies to ISS. The progress spacecraft and its contents are intentionally burned up in the earth's atmosphere during reentry. This manual method of trash management on ISS is a wasteful use of crew time and does not transition well to far term missions.
Different wastes onboard spacecraft vary considerably in their characteristics and in the appropriate method of management. In advanced life support systems for far term missions, recovery of resources such as water from the wastes becomes important. However waste such as plastic food packaging, which constitutes a large fraction of solid waste (roughly 21% on ISS, more on long duration missions), contains minimal recoverable resource. The appropriate management of plastic waste is waste stabilization (or sterilization), volume and resource recovery.
The heat melt compactor takes advantage of the low melting point of plastics to compact plastic materials using a combination of heat and pressure. The US Navy has demonstrated successful development of a similar unit for shipboard application. Ames is building upon the basic approach demonstrated by the Navy to develop an advanced heat melt type compactor for space mission type wastes
Recommended Content
Authors
Citation
Pace, G., Pisharody, S., and Fisher, J., "Plastic Waste Processing and Volume Reduction for Resource Recovery and Storage in Space," SAE Technical Paper 2003-01-2369, 2003, https://doi.org/10.4271/2003-01-2369.Also In
References
- “Design and Fabrication of a Prototype Trash Compacting Unit.” Industrial Ecology, Inc. Los Angeles, CA. April 1973
- McGraw, Peter “Plastics Waste Processor.” Carderock Division, Naval Surface Warfare Center 9500 MacArthur Blvd, West Bethesda, Maryland 20817-5700 301 227 5155
- “SHIPBOARD POLLUTION CONTROL, U.S. Navy Compliance With MARPOL Annex V.” Committee on Shipboard Pollution Control, Naval Studies Board, Commission on Physical Sciences, Mathematics, and Applications, National Research Council NATIONAL ACADEMY PRESS Washington, D.C. 1996
- Wignarajah, K. Fisher, J.W. Pisharody, S. Teleconference Presentation “Solid Waste Model” Feb 19 2003
- Honeywell International Inc. “Design Solutions Guide” Honeywell Plastics 101 Columbia Rd. Morristown, NJ. 07962 2003
- White Paper on ISS Consumables and Waste Disposition June 2001
- Lee, W.C. 2001 “Advanced Life Support SMAP Mars Missions Solid Waste Model (Revision A),” LMSEAT 33552, Lockheed Martin Space Operations Houston, Texas
- Maxwell, S. 2000 “Waste Steam Analysis for STS-99” The Boeing Company, Boeing Space Coast Operations Kennedy Space Center, Florida Internal Boeing Document
- Maxwell, S. 2000 “Waste Steam Analysis for STS-101” The Boeing Company, Boeing Space Coast Operations Kennedy Space Center, Florida Internal Boeing Document
- Wydeven, T. Golub, M.A. 1990 “Waste Streams in a Crewed Space Habitat,” Waste Management and Research 1991 9 91 101
- Hanford, A.J. May 8 2002 “Advanced Life Support Baseline Values and Assumptions Document” National Aeronautics and Space Administration Lyndon B. Johnson Space Center, Houston, Texas