This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Development of a Dimethyl Ether (DME)-Fueled Shuttle Bus
Technical Paper
2003-01-0756
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Dimethyl Ether (DME) is a potential ultra-clean diesel fuel. Its unique characteristics require special handling and accommodation of its low viscosity and low lubricity. In this project, DME was blended with diesel fuel to provide sufficient viscosity and lubricity to permit operation of a 7.3 liter turbodiesel engine in a campus shuttle bus with minimal modification of the fuel injection system. A pressurized fuel delivery system was added to the existing common rail injection system on the engine, allowing the DME-diesel fuel blend to be circulated through the rail at pressures above 200 psig keeping the DME in the liquid state. Fuel exiting the rail is cooled by finned tubed heat exchangers and recirculated to the rail using a gear pump. A modified LPG tank (for use on recreational vehicles) stores the DME- diesel fuel blend onboard the shuttle bus. A small cylinder of helium is used to provide a blanket of inert gas above the fuel mixture to keep the DME in the liquid state and to push the mixture to the fuel rails. A significant challenge is posed by the rapid increase in DME vapor pressure with increasing fuel temperature. As the fuel mixture passes through the rail, it is heated by the surrounding surfaces in the cylinder head. The target for maximum fuel rail temperature was set at 50°C, which corresponds to a DME vapor pressure of 150 psig. Refueling was accomplished by mixing the diesel fuel and DME onboard the bus, with diesel fuel delivered from the existing diesel tank and DME delivered by 1000 lb cylinders at a small refueling station. The shuttle bus operates on the Faculty/Staff loop at the University Park campus of the Pennsylvania State University.
Recommended Content
Authors
- Jennifer Eirich - The Pennsylvania State University
- Elana Chapman - The Pennsylvania State University
- Howard Glunt - The Pennsylvania State University
- David Klinikowski - The Pennsylvania State University
- André L. Boehman - The Pennsylvania State University
- James G. Hansel - Air Products and Chemicals, Inc.
- Edward C. Heydorn - Air Products and Chemicals, Inc.
Topic
Citation
Eirich, J., Chapman, E., Glunt, H., Klinikowski, D. et al., "Development of a Dimethyl Ether (DME)-Fueled Shuttle Bus," SAE Technical Paper 2003-01-0756, 2003, https://doi.org/10.4271/2003-01-0756.Also In
Ci Engine Combustion Processes & Performance With Alternative Fuels
Number: SP-1737; Published: 2003-03-03
Number: SP-1737; Published: 2003-03-03
References
- EPA Final Emission Standards for 2004 and Later Model Year Highway Heavy-Duty Vehicles and Engines (EPA 420-F-00-026) 2000 United States Environmental Protection Agency
- EPA Heavy-Duty Engine and Vehicle Standards and Highway Fuel Sulfur Control Requirements (EPA420-F-00-057) 2000 United States Environmental Protection Agency
- Cheney, D. Powell, C. O'Neill, P. Norton, G. Veneman, A. Evans, D. Mineta, N. Abraham, S. Allbaugh, J. Whitman, C.T. Bolten, J. Daniels, M. Lindsey, L. Barrales, R. Lundquist, A. “National Energy Policy: Reliable, Affordable, and Environmentally Sound Energy for America's Future” 2001 National Energy Policy Development Group, U.S. Government Washington, D.C.
- Phillips, J.G. Reader, G. T. “The Use of DME as a Transportation fuel - A Canadian Perspective.” ASME Fall Technical Conference 1998 31 3 65 71
- Verbeek, R. Van der Weide, J. “Global Assessment of Dimethyl Ether: Comparison with Other Fuels.” Society of Automotive Engineers 1997 971607
- Wakai, K. Nishida, K. Yoshizaki, T. Hiroyasu, H. “Ignition Delays of DME and Diesel Fuel Sprays Injected by a DI Diesel Injector.” Society of Automotive Engineers 1999 1999-01-3600
- Sorenson, S.C. Mikkelsen S. “Performance and Emissions of a DI Diesel Engine Fuelled with Neat Dimethyl Ether.” Society of Automotive Engineers 1995 950064
- Kapus, P.E. Cartellieri, W.P “ULEV Potential of a Car Engine Operated on Dimethyl Ether.” Society of Automotive Engineers 1995 952754
- Fleisch, T. McCarthy, C. Basu, A. Udovich, C. Charbonneau, P. Slodowske, W. Mikkelsen, S. McCandless, J. “A New Clean Diesel Technology: Demonstration of ULEV Emissions on a Navistar Diesel Engine Fueled with Dimethyl Ether.” Society of Automotive Engineers 1995 950061
- Hansen, J.B. Voss, B. “Large Scale Manufacture of Dimethyl Ether -a New Alternative Fuel from Natural Gas.” Society of Automotive Engineers 1995 950063
- Tijm, P. Waller, F. Toseland, B. Peng, X. “‘Liquid Phase Di-Methyl Ether ™, A promising New Diesel Fuel” Proceedings in Energy Frontiers International Conference Alaska 1997
- Maricq, M.M. Szente, J.J. Hybl, J.D. “Kinetic Studies of the Oxidation of Dimethyl Ether and Its Chain Reaction with Cl2.” J. Phys. Chem. A 1997 101 28 5155 5167
- Nash, J.J. Francisco, J.S. “Unimolecular Decomposition Pathways of Dimethyl Ether: An Ab Initio Study.” J. Phys. Chem. A 1998 102 1 236 241
- McMurry, J. Organic Chemistry 4th 1995 Pacific Grove, CA Brooks/Cole Publishing Company
- Marchionna, M. Patrini, R. Giavazzi, F. Pecci, G. “Linear Ethers as High Quality Components for Reformulated Diesel Fuels” Proceedings in Symposium on Removal of Aromatics, Sulfur and Olefins from Gasoline and Diesel presented at the 212th National Meeting (Aug 25-29) American Chemical Society 1996 Orlando, FL 585 589
- Kapus, P. Ofner, H. “Development of Fuel Injection Equipment and Combustion Systems for DI Diesels operated on Dimethyl Ether.” Society of Automotive Engineers 1995 950062
- Riesenberg, K.O. Faupel, W. Blaich, B. Stumpp, G. Ungerer, G. Polach, W. Leonard, R. Schneider, V. Ritter, E. Tschoke, H. Dieter, W. Warga, W. Kaczynski, B. Bauer, H. Diesel Fuel Injection 1st 1994 Stuttgart, Germany Robert Bosch
- Ofner, H. Gill, D.W. Krotscheck, C. “DME as Fuel for CI engines - A New Technology and its Environmental Potential.” Society of Automotive Engineers 1998 981158
- Glensvig, M. Sorenson, S.C. Abata, D. L. “An Investigation of the Injection Characteristics of Dimethyl Ether.” ASME Fall Technical Conference 1997 29 3 77 84
- Johnson, J. Bagley, S. Gratz, L. Leedy, D. “A Review of Diesel Particulate Control Technology and Emissions Effects- 1992 Horning Memorial Award Lecture.” Society of Automotive Engineers 1994 940233
- Schmidt, D. Wong, V. Green, W. Weiss, M. Heywood, J. “Review and Assessment of Fuel Effects and Research Needs in Clean Diesel Technology.” ASME Spring Technical Conference 2001 36 1 23 37
- Nielsen, K. Sorenson, S. “Lubricity Additive and Wear with DME in Diesel Injection Pumps.” American Society of Mechanical Engineers, ICE Fall Technical Conference 1999 33 1 145 153
- Nikanjam, N. “Diesel Fuel Lubricity: On the Path to Specifications.” Society of Automotive Engineers 1999 1999-01-1479
- Bechtold, R. Alternative Fuels Guidebook: Properties, Storage, Dispensing, and Vehicle Facility Modifications 1997 Warrendale, PA Society of Automotive Engineers
- Nabi, M.N. Minami, M. Ogawa, H. Miyamoto, N. “Ultra Low Emission and High Performance Diesel Combustion with Highly Oxygenated Fuel.” Society of Automotive Engineers 2000 2000-01-0231
- Kajitani, S. Chen, Z. L. Konno M. Rhee, K.T. “Engine performance and Exhaust Characterestics of DI Diesel Engine Operated with DME.” Society of Automotive Engineers 1997 972973
- Ikeda, M. Mikami, M. Kojima, N. “Exhaust Emission Characteristics of DME/Diesel Fuel Engine.” Society of Automotive Engineers 2000 2000-01-2006
- Chen, Z. Kajitani, S. Minegisi, K. Oguma, M. “Engine Performance and Exhaust Gas Characteristics of a Compression Ignition Engine Operated with DME blended Gas Oil Fuel.” Society of Automotive Engineers 1998 982538
- Rubino, L. Thompson, M.J. “The Effect of Oxygenated Additives on Soot Precursor Formation in a Counterflow Diffusion Flame.” Society of Automotive Engineers 1999 993589
- Mikkelsen, S. Hansen, J. Sorenson, S. Dimethyl Ether as an Alternate Fuel for Diesel Engines, in Application of Powertrain and Fuel Technologies to Meet Emissions Standards Mardell J. Parsons, M. Read, J. Lemon, D. 1996 Professional Engineering Publishing Limites for IMechE London, UK 289
- Christensen, R. Sorenson, S.C. “Engine Operation on DME in a Naturally Aspirated DI Diesel Engine.” Society of Automotive Engineers 1997 971665
- Hupperich, P. Dürnholz, M. Hüchtebrock, B. “Diesel Oil, Water in Carbon Fuel Emulsion, DME or Natural gas? - Comparative tests on a Single Cylinder Engine.” ASME Fall Technical Conference 1997 29 3 61 67
- Hallgren, B. Heywood, J. “Effects of Oxygenated Fuels on DI Diesel Combustion and Emissions.” Society of Automotive Engineers 2001 2001-01-0648
- Hess, H.S. Roan, M.A. Bhalla, S. Butnark, S. Zarnescu, V. Boehman, A.L. Tijm, P.J.A. Waller, F.J. Chemistry of Diesel Fuels “The Use of Oxygenated Diesel Fuels for Reduction of Particulate Emissions from a Single-Cylinder Indirect Injection Engine,” Applied Energy Technology Series Song C. Hsu, C. Mochida, I. 2000 New York, NY Taylor & Francis 255 268
- Litzinger, T. Stoner, M. Hess, H. Boehman, A. “Effects of Oxygenated Blending compounds on Emissions from a Turbo-charged Direct Injection Diesel Engine.” Int. J. Engine Research 2000 1 57 70
- Stoner, M. Litzinger, T. “Effects of Structure and Boiling Point of Oxygenated Blending Compounds in Reducing Diesel Emissions.” Society of Automotive Engineers 1999 991475
- Murayama, T. Zheng, M. Chikahisa, T. Oh, Y.-T. Fujiwara, Y. Tosaka, S. Yamashita, M. Yoshitake, H. “Simultaneous Reductions of Smoke and NOx from a DI Diesel Engine Using EGR and Dimethyl Carbonate.” Society of Automotive Engineers 1995 952518
- Hess, H. Szybist, J. Boehman, A. Tijm, P. Waller, F. “The Use of CETANER™ for the Reduction of Particulate Matter Emissions in a Turbocharged Direct Injection Medium-Duty Diesel Engine” Proceedings in Seventeenth Annual International Pittsburgh Coal Conference September 11-15 2000 Pittsburgh, PA
- Amano, T. Dryer, F. L. “Effect of DME, NOx, And Ethane or CH4 Oxidation: High Pressure, Intermediate - Temperature Experiments And Modelling.” Twenty Seventh International Combustion Symposium Proceedings 1998 397 404
- Curran, H. Pitz, W. Westbrook, C. Dagaut, P. Boettner, J-C. Cathonnet, M. “A Wide Range Modeling Study of Dimethyl Ether Oxidation.” Inter. Journal of Chemical Kinetics 1998 30 3 229 241
- Hansen, K. Nielsen, L. Hanses, J. Mikkelsen, S. Landalv, H. Ristola, T. Vielwerth, K. “Demonstration of a DME (Dimethyl Ether) Fuelled City Bus.” Society of Automotive Engineers 2000 2000-01-2005
- Okutsu, S. “NKK Begins DME Vehicle Road Test” http://www.nkk.co.jp/en/environment/dme/index.html 2002 NKK Tokyo, Japan
- Sorenson, S.C. Glensvig M. Abata Duane L “Dimethyl Ether in Diesel Fuel Injection Systems.” Society of Automotive Engineers 1998 981159
- Wakai, K. Yoshizaki, T. “Numerical and Experimental Analyses of the Injection Characteristics of Dimethyl Ether with a DI Diesel Injection System.” Society of Automotive Engineers 1999 1999-01-1122
- Konno, M. Kajitani, S. Oguma, M. Iwase, T. Shima, K. “NO Emission Characteristics of a CI Engine Fueled with Neat Dimethyl Ether.” Society of Automotive Engineers 1999 1999-01-1116
- Chapman, E. Bhide, S. Boehman, A. Tijm, P.J.A. Waller, F.J. “Emission Characteristics of a Navistar 7.3L Turbodiesel Fueled with Blends of Oxygenates and Diesel.” Society of Automotive Engineers 2000 2000-01-2887
- Chapman, E. Boehman, A. Tijm, P.J.A. Waller, F. “Emissions Characteristics of a Navistar 7.3L Turbodiesel Fueled with Blends of Dimethyl Ether and Diesel Fuel.” Society of Automotive Engineers 2001 Transactions-Journal of Fuels & Lubricants 2001 110 2001-01-3626 2166 2175
- Bhide, S.V. Boehman, A.L. Perez, J.M. “Viscosity of DME-Diesel Fuel Blends,” ACS Fuel Chemistry Division Preprints 46 2 400 401 2001
- SAE SAE J1739 “Potential Failure Mode and Effects Analysis (Design FMEA) and Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA Reference Manual)” 1999 SAE Handbook 1999
- DuPont Dymel A Technical Information ATB-25 1992 Fluorochemicals Laboratory, E.I. duPont de Nemours and Company