This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Highly Loaded P/M Gears Produced by Selective Surface Densification
Technical Paper
2003-01-0334
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This paper reviews the current development status of highly loaded P/M gears. It is shown that surface densified P/M steels can sustain typical stresses in gears generated by bending of the tooth and rolling contact fatigue at the tooth flank. Specifically, the design of the preform and the corresponding density distribution in the gear after rolling is described. Results from load tests of various P/M steels which simulate tooth root and flank loading are discussed and compared to a standard gear steel (16MnCr5). Finally, it is shown that P/M gears manufactured by selective surface densification combine mechanical performance with a significant cost savings potential.
Recommended Content
Authors
Citation
Rau, G., Sigl, L., and Krehl, M., "Highly Loaded P/M Gears Produced by Selective Surface Densification," SAE Technical Paper 2003-01-0334, 2003, https://doi.org/10.4271/2003-01-0334.Also In
References
- Lipp K. Hoffmann G. “Design for Rolling Contact Fatigue” Proceedings PM 2 Tech World Congress 2002 Orlando FL 5/28 5/52 2002
- Strehl R. “Tragfähigkeit von Zahnrädern aus hoch-festen Sinterstählen” Germany 1997
- Engström U. Johansson B. “Experience with Warm Compaction of Densmix Powders in the Production of Complex Parts” Proceedings Powder Metallurgy World Congress 2000 Kyoto (Japan) 536 539 2000
- Skoglund P. Kejzelman M. Hauer I. “HVC punches PM to new mass production limits” Metal Powder Report 57 9 26 30 2002
- Bode U. “Powder Forging for Engine Transmission Parts” Euro PM 2000 Processing for High Density 117 122 2000
- Link R. Kotthoff G. “Suitability of high density powder metal gears for gear application” Gear Technology 18 1 15 18 2001
- Alvier Technical Brochure “Schrägverzahnung, Ver-dichtungskonzept und allgemeine Bedingungen für schrägverzahnte PM-Teile” Alvier AG, Buchs Switzerland 2001
- Bengtsson S. Fordén L. Dizdar S. Johansson P. “Surface Densified P/M Transmission Gear” 2001 International Conference on Power Transmission Components. Advances in High Performance Powder Metallurgy Applications October 16-17 1 25 2001
- Bengtsson S. Fordén L. Kuylenstierna L. Kuylenstierna C. “Performance and properties of surface densified PM transmission gears” Proceedings PM 2 Tech World Congress 2002 Orlando FL 2/50 2/63 2002
- Bengtsson S. Fordén L. “Rolling Contact Fatigue Tests of Selectively Densified Materials” Proceedings PM 2 Tech World Congress 2001 New Orleans LO 10/71 10/86 2001
- Johansson P. Bengtsson S. Dizdar S. “RCF-testing of selectively densified rollers of P/M materials for gear applications” Proceedings PM 2 Tech World Congress 2002 Orlando FL 5/180 5/192 2002
- Kotthoff G. „Nachverdichten der Randzone von Sinterzahnrädern - Grundlagen-untersuchungen zur Wälzfestigkeit an Rollen” 43. Arbeitstagung “Zahn-rad- und Getriebeuntersuchung” WZL, Technical University of Aachen April 2002 6 49 2002
- Sandner Ch. Ratzi R. Lorenz B. Tobie T. “Sintered Gears: Achievable Load-Carrying Capacities by Conventional and New Production Methods” VDI-Report Nr. 1665 2002
- Lipp K. “Oberflächenzerrüttung von Sinterstählen unter konstanter und veränderlicher Hertz'scher Pressung mit überlagerter Reibung (Schlupf)” Internal Report Nr. FB-210 1997