This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Automotive Ignition Transfer Efficiency
Technical Paper
2002-01-2839
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Measurement and analysis of typical automotive spark ignitions operating up to 30Kv and 30 to 100ma show the electrical-to-plasma (energy) transfer efficiency to be very low, significantly less than one-percent (1%).1 The reason for this low energy transfer efficiency is high resistance in the driving circuit that is in series with the rather low resistance of the ignition spark. The largest components of resistance are in the ignition coil and the high voltage cables.
The latest evolution of ignition systems has been the elimination or severe shortening of the high voltage cable and the incorporation of one ignition coil attached directly to the individual spark plug. While this has eliminated much, and in some cases all, of the transfer losses attributed to the cables, the system as a whole is still very inefficient in the electrical-to-plasma conversion efficiency because the spark coil and spark plugs still have many times the resistance of the spark discharge channel.
These systems will therefore not meet the needs of future lean burn and alternative fuel engines requiring higher energy discharges to effectively ignite the fuel mixtures.2, 3, 4, 5 A further complication is the present requirement to reduce the power consumption of the ignition system.
There are two basic approaches to increasing the electrical efficiency of ignition systems. Either will reduce average power consumption. The first is to design the coil circuit with low resistance, which would require upgraded electrical components to handle higher currents. The second and most practical is to use a peaking capacitor between the coil output and the spark plug. With the second alternative, energy transfer efficiencies approaching 50% can be achieved using existing ignition components.1
This paper will present a general analysis of conventional and modified ignition systems and the data from measurements of an ignition system with a peaking capacitor. Recommendations for increasing general ignition efficiency and effectiveness will also be included.
Recommended Content
Topic
Citation
Rohwein, G. and Camilli, L., "Automotive Ignition Transfer Efficiency," SAE Technical Paper 2002-01-2839, 2002, https://doi.org/10.4271/2002-01-2839.Also In
References
- Rohwein G.J. “An Efficient, Power Enhanced Ignition System” IEEE Transactions on Plasma Science 25 2 April 1997
- Ziegler G.F.W. Maly R.R. Wagner E.P “Effects of Ignition System Design on Flammability Requirements On Ultra-Lean Turbulent Mixtures” I. Mech. E. , paper no. C47/83 1983
- Maly R. Saggau B. Wagner E. Ziegler G. “Prospects of Ignition Enhancement” SAE Paper 830478 Feb. 1983
- Anderson R.W. “The Effects of Ignition System Power On Fast-Burn Engine Combustion” SAE paper 870549 Feb. 1987
- Anderson R.W. Asik J.R. “Lean Air-Fuel Ignition System Comparison In a Fast-Burn Engine” SAE paper 850076 Feb. 1985
- Ball G.A. Gross J.V. “Evaluation Of a Hard Discharge Ignition System” Advance Powerplant Engineering Chrysler Corporation Mar. 1986
- Maly R. “Spark Ignition: Its Physics and effects on the Internal Combustion Process” Fuel Economy in Road Vehicles Powered By Spark Ignition Engines Hilliard, J.C. Springer, G.S. Plenum New York 1984
- Martin J.C. “Duration of the Resistive Phase and Inductance of Spark Channels” AFWL Switching Note 9 1965
- Sorensen T.P. Ristic V.M. “Rise Time and Time-Dependant Spark-Gap Resistance in Nitrogen and Helium” J. Appl. Phys . 48 1 114 117 1977
- Lux V. “Sparking Plug” Jul. 1915
- New Mexico Highway Department Report April 5 1995 Leonard Richard
- Environmental Testing Corp. Denver Colorado FCCS, Control Number ComTec767189 Oct. 1994
- September 15 1997
- March 24 2000