This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Influence of Atomization Quality on Mixture Formation, Combustion and Emissions in a MPI-Engine Under Cold-Start Conditions, Part I
Technical Paper
2002-01-2807
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The study presented in this two part paper was focused on the influence of primary mixture formation on engine running behavior covering the areas combustion and raw emissions. Two different concepts for primary fuel atomization were utilized and compared, the standard production injector and a flash boiling injector. The spray generated by the flash boiling injector was characterized by a significant reduction in droplet size and a partial direct vaporization during the injection process by preheating the fuel inside the injector. In this study special emphasis was put on the transient process of engine start between typical cooling water temperatures of -7°C and 85°C. Various measurements and visualization techniques were applied to investigate the mixture preparation, the deposition of liquid fuel on the walls, the start of combustion, and in-cylinder and engine-out UHC emissions.
Recommended Content
Authors
- Boyke Richter - Institute for Thermal Turbomachinery, University of Karlsruhe
- Klaus Dullenkopf - Institute for Thermal Turbomachinery, University of Karlsruhe
- Sigmar Wittig - Institute for Thermal Turbomachinery, University of Karlsruhe
- Jan Tribulowski - Institute for Reciprocating Engines, University of Karlsruhe
- Ulrich Spicher - Institute for Reciprocating Engines, University of Karlsruhe
Topic
Citation
Richter, B., Dullenkopf, K., Wittig, S., Tribulowski, J. et al., "Influence of Atomization Quality on Mixture Formation, Combustion and Emissions in a MPI-Engine Under Cold-Start Conditions, Part I," SAE Technical Paper 2002-01-2807, 2002, https://doi.org/10.4271/2002-01-2807.Also In
References
- Zhao, F.Q. Lai, M.C. Harrington, D.L. “A Review of Mixture Preparation and Combustion Control Strategies for Spark-Ignited Direct-Injection Gasoline Engines” SAE Technical Paper No. 970627
- Roberts, E.C. Stanglmaier, R.H. “Investigation of Intake Timing Effects on the Cold Start Behavior of a Spark Ignition Engine” SAE Technical Paper No. 1999-01-3622 1999
- Zimmermann, F. Bright, J. Ren, W.M. Imoehl, B. “An Internally Heated Tip Injector to Reduce HC Emissions During Cold Start” SAE Technical Paper No. 1999-01-0792 1999
- Fulcher, S.K. Gajdeczko, B.F. Felton, P.G. Bracco, F.V. “The Effects of Fuel Atomization, Vaporization, and Mixing on the Cold-Start UHC Emissions of a Contemporary S.I. Engine with Intake-Manifold Injection” SAE Technical Paper No. 952482 1995
- Bielaczyc, P. Merkisz, J. “Exhaust Emission from Passenger Cars during Engine Cold Start and Warm Up” SAE Technical Paper No. 970740
- Rottenkolber, G. Kölmel, A. Dullenkopf, K. Wittig, S. Feng, B. Spicher, U. “Influence of Mixture Preparation on Combustion and Emissions Inside an SI Engine by Means of Visualization, PIV and IR Thermography During Cold Operating Conditions” SAE Technical Paper No. 1999-01-3644
- Zhao, F.-Q. Lai, M.-C. Harrington, D. “The Spray Characteristics of Automotive Port Fuel Injection - A Critical Review” SAE Technical Paper No. 950506
- Ohyama, Y Yamauchi, T. Ohsuga, M. “Mixture Formation during Cold Starting and Warm Up in Spark Ignition Engines” SAE Technical Paper No. 960065
- 9 Shayler, P.J. Davies, M:T: Scarsbrick, A. “Stored and Lost Fuel Quantities after Engine Start-Up” SAE Technical Paper No. 974133
- Meyer, R. Heiwado, J.B. “Liquid Fuel Transport Mechanisms into the Cylinder of a Firing Port-Injected SI Engine during Start Up” SAE Technical Paper No. 970865
- Namiyama, K. Nakamura, H. Kokubo, K. Hosogai, D. “Development of Ultrasonic Atomizer and its Application to S.I. Engines” SAE Technical Paper No. 890430 1989
- Harada, K. Shmizu, R. Kurita, K. Muramatsu, M. Makimura, T. Ohashi, M. “Development of Air-Assisted Injector System” SAE Technical Paper No. 920249 1992
- Williams, P.A. Jackson, S.D. MA, T.H. “An examination of SI engine cold start mixture preparation - comparison between liquid and vapour fuel presentation” ImechE 1998, C524/024/97
- Hofmann, P. Lenz, H. P. “Ein schnell ansprechendes Flash-Boiling-Einspritzventil zur Verminderung der Emissionen im Kaltstart und Warmlauf” 21. Internationales Wiener Motorensymposium 2000
- Tribulowski, J. Spicher, U. Richter, B. Dullenkopf, K. Wittig, S. “Influence of Atomization Quality on Mixture Formation, Combustion and Emissions in a MPI-Engine Under Cold-Start Conditions, Part II” SAE Technical Paper No. 02FFL-91
- Rottenkolber, G. Dullenkopf, K. Wittig, S. “Visualization and PIV-Measurements inside the Intake Port of an IC-Engine” 9 th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal 1998
- 17 Roth, N. Anders, K. Frohn, A. “Refractive-index measurements for the correction of particle sizing methods” Applied Optics 30 33 1991
- Rottenkolber, G. Dullenkopf, K. Wittig, S. “Two Phase PIV Measurements inside the Intake Port of an IC-Engine” Proceedings of VSJ-SPIE 98 Yokohama, Japan paper AB085 December 1998