This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Modelling Methodology of a Spark-Ignition Engine and Experimental Validation: Part I: Single-Zone Combustion Model
Technical Paper
2002-01-2193
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This paper describes a general procedure for defining a fuel heat release function to be used in a single-zone combustion model of a spark-ignition engine using crank-angle resolved analysis of the pressure. The combustion model parameters to identify are the combustion angles and the Vibe function coefficients. Furthermore, the cylinder wall temperature is identified using the cylinder pressure during the closed-valve period of the compression stroke, and the heat transfer correlation (Woschni's correlation) is tuned according to the difference between the fuel heat release and the net heat release. The fuel heat release is determined with the polytropic index first law model. This heat addition due to combustion is verified by reference to the fuel consumption and combustion efficiency. Combustion efficiency is determined from the exhaust gas composition.
In this way, the combustion parameters are identified and the heat transfer correlation is verified for an engine at different loads and engine speeds. The experimental data used are the crank-angle resolved cylinder pressure and the measurements in a typical engine dynamometer test: engine speed, load, fuel consumption, AFR and air charge conditions.
Finally a full comparison of experimental cylinder pressures and single-zone model results is made with the conclusion being reached that the combustion parameters were correctly identified.
Recommended Content
Authors
Topic
Citation
Grau, J., García, J., García, J., Robles, A. et al., "Modelling Methodology of a Spark-Ignition Engine and Experimental Validation: Part I: Single-Zone Combustion Model," SAE Technical Paper 2002-01-2193, 2002, https://doi.org/10.4271/2002-01-2193.Also In
References
- Brunt M.F.J. Emtage A.L. Evaluation of Burn Rate Routines and Analysis Errors SAE paper 970037 1997
- Brunt M.F.J. Rai H. Emtage A.L. The Calculation of Heat Release Energy from Engine Cylinder Pressure Data SAE paper 981052 1998
- Rassweiler G.M. Withrow L. Motion Pictures of Engine Flames Correlated with Pressure Cards SAE Transaction 42 185 204 1938
- Heywood J.B. Internal Combustion Engine Fundamentals 386 388 McGraw - Hill Book Company 0-07-100499-8 1988
- Ferguson C.R. Internal Combustion Engine Applied Thermosciences 169 180 John Wiley 1986
- Shayler P.J. May S.A. Ma T. The Determination of Heat Transfer from the Combustion Chambers of SI engines SAE Paper 931131 and VTMS Conf. Proc 1993
- Hayes T.K. White R.A. Peters J.E. Combustion Chamber Temperature and Instantaneous Local Heat Flux Measurements in a Spark Ignition Engine SAE paper 930217 1993
- Erikssson Lars Requeriments for and a Systematic Method for Identifying Heat-Release Model Parameters SAE paper 980626 1998
- Arsie I. Pianese C. Rizzo G. Development and Identification of a Hierarchical System of Models for Rapid Prototyping of SI Engines Proc. of the 6th IEEE Mediterranean Conference on “Control Systems” Alghero, Italy June 9-11 1998
- Douglas R. Kee R.J. Carberry B.P. Analysis of In-Cylinder Pressure Data in Two-Stroke Engines SAE paper 972792 1997
- Brunt M.F.J. Rai H. Emtage A.L. The Calculation of Heat Release Energy From Engine Cylinder Pressure Data SAE paper 981052 1998
- Brunt M.F.J. Kieron C.P. Calculation of Heat Release in Direct Injection Diesel Engines SAE paper 1999-01-0187 1999
- Guezennec Yann G. Wajdi Hamama Two-Zone Heat Release Analysis of Combustion Data and Calibration of Heat Transfer Correlation in an I. C. Engine SAE paper 1999-01-0218 1999
- Blair G.P. Design and Simulation of Two-Stroke Engines 289 293 SAE publications 1996
- Heywood J.B. Internal Combustion Engine Fundamentals 154 McGraw-Hill Book Company 1988
- Vibe I.I. VEB Verlag Technik Berlin 1970
- van Nieuwstadt M.J. Kolmanovsky I.V. Brehob D. Haghgooie M. Heat Release Regressions for GDI Engines SAE paper 2000-01-0956 2000
- Wolfram Research Mathematica 3.0 Standard Add-on Packages 460 468 Wolfram Media and Cambridge University Press 1996
- Cheung H.M. Heywood J.B. Evaluation of a one-zone burn-rate analysis procedure using production SI engine pressure data SAE paper 932749 1993
- Arsie I. Flauti G. Pianese C. Rizzo G. Cylinder Thermal State Detection From Pressure cycle in SI Automotive engines IFAC 2000
- Grau J. Hernandez García J. Martínez García J. Perez Robles A. Viedma Pastor R. Royo Modelling Methodology of a Spark-Ignition Engine and Experimental Validation. Part II: Gas exchange Process SAE paper 2002-01-2194 2002
- Stas Marek J. An Universally Applicable Thermodynamic Method for TDC Determination SAE paper 2000-01-0561 2000
- Brunt M.F.J. Gordon G. The Effect of Crank Angle Resolution on Cylinder Pressure Analysis SAE paper 910041 1991
- Randolf A.L. Cylinder-Pressure-Based Combustion Analysis in Race Engines SAE paper 942487 1994
- Brunt M.F.J. Pond C.R. Evaluation of Techniques for Absolute Cylinder Pressure Correction SAE paper 970036 1997
- IMST Thermal Systems Research and Modelling http://www.imst.upv.es 2001
- Brunt M.F.J. Emtage A.L. Evaluation of IMEP Routines and Analysis Errors SAE paper 960609 1996