This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Development of the High Power NADI™ Concept Using Dual Mode Diesel Combustion to Achieve Zero NOx and Particulate Emissions
Technical Paper
2002-01-1744
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Due to their high thermal efficiency coupled with low CO2 emissions, Diesel engines are promised to an increasing part of the transport market if their NOx and particulate emissions are reduced. Today, adequate after-treatments, NOx and PM traps are under industrialization with still concerns about fuel economy, robustness, sensitivity to fuel sulfur and cost because of their complex and sophisticated strategy.
New combustion process such as Homogeneous Charge Compression Ignition (HCCI) are investigated for their potential to achieve near zero particulate and NOx emissions. Their main drawbacks are too high hydrocarbons (HC) and carbon monoxide (CO) emissions, combustion control at high load and then limited operating range and power output.
As an answer for challenges the Diesel engine is facing, IFP has developed a combustion system able to reach near zero particulate and NOx emissions while maintaining performance standards of the D.I Diesel engines. This “dual mode” engine application called NADI™ (Narrow Angle Direct Injection) applies Homogeneous Charge Compression Ignition at part load and switches to conventional Diesel combustion to reach full load requirements.
At part load (including MVEG and FTP cycles), HCCI combustion mode allows near zero particulate and NOx emissions and maintains very good fuel efficiency close to an EURO III Diesel engine. At 1500 and 2500 rpm, NADI™ reaches 6 and 9 bar of IMEP with emissions of NOx and particulate under 0.05 g/kWh which means respectively 100 times and 10 times lower than a conventional Diesel engine.
At full load, NADI™ system is consistent with future Diesel engine power density standard. At 4000 rpm, 50/55 kW/l has been reached with conventional limiting factors and engine parameters settings.
Further development steps are also well identified, using advanced engine technology such as further generation of common rail fuel injection system, VVA or electric assisted turbocharger.
Recommended Content
Authors
Topic
Citation
Walter, B. and Gatellier, B., "Development of the High Power NADI™ Concept Using Dual Mode Diesel Combustion to Achieve Zero NOx and Particulate Emissions," SAE Technical Paper 2002-01-1744, 2002, https://doi.org/10.4271/2002-01-1744.Also In
References
- Stanglmaier R. H. Roberts C. E. «Homogeneous Charge Compression Ignition (HCCI): Benefits, Compromises, and Future Engine Applications» SAE Paper 1999-01-3682 1999
- Pucher G. R. Gardiner D. P. Bardonand M. F. Battista V. «Alternative Combustion Systems for Piston Engines Involving Homogeneous Charge Compression Ignition Concepts - A review of Studies Using Methanol, Gasoline and Diesel Fuel» SAE Paper 962063 1996
- Najtand P. M. Foster D. E. «Compression - Ignited Homogeneous Charge Combustion» SAE Paper 830264 1983
- Christensen M. Hultqvist A. Johansson B. «Demonstrating the Multi Fuel Capability of a Homogeneous Charge Compression Ignition Engine with Variable Compression Ratio» SAE Paper 1999-01-3679 1999
- Christensen M. Johansson B. «Supercharged Homogeneous Charge Compression Ignition (HCCI) with Exhaust Gas Recirculation and Pilot Fuel» SAE Paper 2000-01-1835 2000
- Yokota H. Nakajima H. Kakegawa T. «A new Concept for Low Emission Diesel Combustion (2 nd Rep.: Reduction of HC and CO Emission, and Improvement of Fuel Consumption by EGR and MTBE Blended Fuel» SAE Paper 981933 1998
- Yanagihara H. Sato Y. Mizuta J. «A simultaneous reduction of NOx and soot in diesel engines under A new combustion system (Uniform Bulky Combustion System - UNIBUS» VDI 1996 267 1996
- Iwabuchi Y. Kawai K. Shoji T. Takeda Y. «Trial of New Concept Diesel Combustion System - Premixed Compression - Ignited Combustion» SAE Paper 1999-01-0185 1999
- Hashizume T. Miyamoto T. Akagawa H. Tsujimura K. “Combustion and Emission Characteristics of Multiple Stage Diesel Combustion.” SAE Paper 980505 1998
- Shimazaki N. Akagawa H. Tsujimura K. «An Experimental Study of Premixed Lean Diesel Combustion» SAE Paper 1999-01-0181 1999
- Kimura S. Aoki O. Kitahara Y. Aiyoshizawa E. «Ultra - Clean Combustion Technology Combining a Low - Temperature and Premixed Combustion Concept for Meeting Future Emission Standards« SAE Paper 2001-01-0200 2001
- Odaka M. Suzuki H. Koike N. Ishii H. «Search for Optimizing Method of Homogeneous Charge Diesel Combustion» SAE Paper 1999-01-0184 199
- Amsden A.A. O'Rourke P.J. Butler T.D. “KIVA-II: a Computer Program for Chemically Reactive Flows with Sprays” Los Alamos LA-11560-MS 1989
- Habchi C. Torres A. “A 3D Multi-Block Structured Version of the KIVA 2 Code” First European CFD Conference proceedings 502 512 1992
- Torres A. Henriot S. “3D Modeling of Combustion in Lean Burn Four Valves Engines: Influence of Intake Configuration” 3 th International Symposium on diagnostics and Modeling of combustion in Internal Combustion Engines COMODIA 1994
- Chalak Z. “Modélisation du délai d'auto-inflammation dans un moteur Diesel; Validation expérimentale” Thèse PhD Université de Rouen 1990
- Magnussen B.F. Hjertager B.H. “On Mathematical Modeling of Turbulent Combustion with Special Emphasis on Soot formation and Combustion” 16 th Symposium on Combustion Combustion Institute 719 729 1976
- Diwakar R. “Assessment of the Ability of a Multidimensional Computer Code to Model Combustion in a Homogeneous Charge Engine” SAE paper 840230 1984