This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Advanced Urea SCR Catalysts for Automotive Applications
Technical Paper
2001-01-0514
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Event:
SAE 2001 World Congress
Language:
English
Abstract
The LEV II and EURO V legislation in 2007/2008 require a high conversion level for nitrogen oxides to meet the emission levels for diesel SUVs and trucks. Therefore, U.S. and European truck manufacturers are considering the introduction of urea SCR systems no later than model year 2005. The current SCR catalysts are based mainly on systems derived from stationary power plant applications. Therefore, improved washcoat based monolith catalysts were developed using standard types of formulations. These catalysts achieved high conversion levels similar to extruded systems in passenger car and truck test cycles. However, to meet further tightening of standards, a new class of catalysts was developed. These advanced type of catalytic coatings proved to be equivalent or even better than standard washcoat formulations. Results will be shown from ESC, MVEG and US-FTP 75 tests to illustrate the progress in catalyst design for urea SCR. The new catalyst systems show a very good aging performance and will be the next generation of urea SCR catalysts for mobile applications.
Recommended Content
Technical Paper | Improved SCR Systems for Heavy Duty Applications |
Technical Paper | Modeling of SCR DeNOx Catalyst - Looking at the Impact of Substrate Attributes |
Technical Paper | Catalytic Converter Design from Mat Material Coupon Fragility Data |
Authors
Citation
Gieshoff, J., Pfeifer, M., Schäfer-Sindlinger, A., Spurk, P. et al., "Advanced Urea SCR Catalysts for Automotive Applications," SAE Technical Paper 2001-01-0514, 2001, https://doi.org/10.4271/2001-01-0514.Also In
Diesel Exhaust Emissions Control: Developments in Regulation and Catalytic Systems
Number: SP-1581; Published: 2001-03-05
Number: SP-1581; Published: 2001-03-05
References
- Iwamoto M. Yokoo S. Sakai K. Kagawa S. J. Chem. Soc., Faraday Trans. 77 1981 1629 1638 Iwamoto M. Yahiro H. Mine Y. Kagawa S. Chem. Lett. 1989 213 216 Iwamoto M. Yahiro H. Tanda K. Mizuno N. Mine Y. Kagawa S. J. Phys. Chem. 95 1991 3727 3730 Iwamoto M. Yohiro H. Mizuno N. Zang W. Mine Y. Furukawa H. Kagawa S. J. Phys. Chem. 96 1992 9360 9366
- Li Y. Hall W.K. J. Catal. 129 1991 202 215
- Kawanami M. Okumura A. Horiuchi M. Schäfer-Sindlinger A. Zerafa K. SAE Technical Paper No. 961129
- Baacke M. Brand R. Engler B. Kiss A. Kleine-Möllhoff P. Kleinschmidt P. Koberstein E. Siray M. 14 12 1988
- Janssen J.J. “Environmental Catalysis - Stationary Sources” Handbook of Catalysis 4 1636 1644 Ertl G. Knözinger H. Weitkamp J. Wiley-VCh Weinheim 1997
- Jacob E. Emmerling G. Döring A. Graf U. Harris M. van den Tillaart J.A.A. Hupfeld B. 19 Vienna Engine Symposium 1998
- Gieshoff J. Schäfer-Sindlinger A. Spurk P.C. van den Tillaart J.A.A. SAE Technical Paper No. 2000-01-0189
- Centi G. Perathoner S. Shioya Y. Anpo M. Res. Chem. Intermed. 17 1992 125 135
- Mishima H. Hashimoto K. Ono T. Anpo M. Applied Catalysis B: Environmental 19 1998 119 129
- Iwamoto M. Hamada H. Catal. Today 17 1991 94 Shelef M. Montreuil C.N. Jen H.W. Catalysis Letters 26 1994 277 284