This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Performance of Newly Developed Plasma Jet Igniter
Technical Paper
1999-01-3327
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The investigation regarding the performance of newly developed plasma jet igniter is explored by using vessel. In plasma jet ignition, combustion enhancement effects occur toward the plasma jet issuing direction. Therefore, when the igniter is attached at the center of cylindrically shaped combustion chamber, plasma jet should issue toward the round combustion chamber wall. The plasma jet igniter that had a concentric circular orifice has been developed. The maximum combustion pressure increases and the burning period decreases with increasing the cavity volume. This feature is similar to that of the ordinary plasma jet igniter. However, the combustion enhancement effect is almost independent of the orifice area.
Recommended Content
| Technical Paper | A STUDY ON THE PLASMA JET DIFFUSIVE COMBUSTION |
| Technical Paper | Relationship between Plasma Jet and Newly Developed Plasma Jet Igniter |
| Technical Paper | The Transfer Function of Combustion Noise in DI-Diesel Engine |
Authors
Citation
Yoshida, K., Shoji, H., and Tanaka, H., "Performance of Newly Developed Plasma Jet Igniter," SAE Technical Paper 1999-01-3327, 1999, https://doi.org/10.4271/1999-01-3327.Also In
References
- Gupta, H. C. Steinberger, R. L. Bracco, F. V. “Combustion in a Divided Chamber, Stratified Charge, Reciprocating Engine: Initial Comparisons of Calculated and Measured Flame Propagation” Combustion Science and Technology 22 27 61 1980
- Cattolica, R. Vosen, S. “Combustion-Torch Ignition: Fluorescence Imaging of OH Concentration” Combustion and Flame 68 267 281 1987
- Kumagai, S. Sakai, T. “Ignition of Gases by High-Energy Sparks” Eleventh Symposium (International) on Combustion 995 1001 1966
- Matthews, R. D. Hall, M. J. Faidley, R. W. Chiu, J. P. Zhao, X. W. Annezer, I. Koening, M. H. Harber, J. F. Darden, M. H. Weldon, W. F. Nichols, S. P. “Further Analysis of Railplugs as a New Type of Ignitor” SAE Paper 922167 1992
- Oppenheim, A. K. Beltramo, J. Faris, D. W. Maxson, J. A. Hom, K. Stewart, H. E. “Combustion by Pulsed Jet Plums - Key to Controlled Combustion Engines” SAE Paper 890153 1989
- Rao Mittinti, D. N. Dabora, E. K. “Plasma Jet Ignition Studies” Twentieth Symposium (International) on Combustion 169 177 1984
- Clements, R. M. Smy, P. R. Dale, J. D. “An Experimental Study of the Ejection Mechanism for Typical Plasma Jet Igniters” Combustion and Flame 42 287 295 1981
- Cavolowsky, J. A. Fairs, D. W. Oppenheim, A. K. “Formation of a Plasma Puff” SAE Paper 870609 1987
- Clements, R. M. Smy, P. R. Topham, D. Vince, I. M. Vovelle, C. Weinberg, F. J. “Chemical Activity and Transport Processes in the Vicinity of a Plasma Jet Igniter” Combustion and Flame 57 265 274 1984
- Yoshida, K. Saima, A. “Influence of Electrical Supplied Energy and Characteristic Length on the Plasma Jet Ignition” SAE Paper 932750 1993
- Yoshida, K. Shoji, H. Saima, A. “Influence of the Characteristic Length on Performance of Plasma Jet Igniters” SAE Paper 942051 1994
- Takagi, K. Ohta, M. Yoshida, K. Shoji, H. Saima, A. “The Influence of the Hot Gas Jet on the Initial Flame Propagation in Plasma Jet Ignition” Proceedings of The First Asia-Pacific Conference on Combustion 480 483 1997
- Wiriyawit, S. Dabora, E. K. “Modeling the Chemical Effects of Plasma Jet Ignition in One-Dimensional Chamber” Twentieth Symposium (International) on Combustion 179 186 1984
- Cetegen, B. Teichman, K. Y. Weinberg, F. J. Oppenheim, A. K. “Performance of a Plasma Jet Igniter” SAE Paper 800042 1980
- Solomon, A. S. “Plasma-Jet Ignition of Fuel Sprays in a Rapid Compression Machine” SAE Paper 880205 1988
- Tanaka, K Yoshida, K. Shoji, H. Tanak, H. “Relationship between Plasma Jet and Newly Developed Plasma Jet Igniter” SAE Paper 982564 1998