This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Quantification and Reduction of IMEP Errors Resulting from Pressure Transducer Thermal Shock in an S.I. Engine
Technical Paper
1999-01-1329
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A major problem with making accurate cylinder pressure measurements using piezoelectric pressure transducers in IC engines is thermal shock. This affects most derived parameters although the greatest error is in the indicated mean effective pressure (IMEP), which can be affected by over 10%. In this paper, thermal shock has been quantified for a wide range of engine conditions. Thermal shock was found to be most significant at low engine speeds, high loads and advanced ignition timings. A good correlation between thermal shock and peak pressure has been established for Kistler 6123 and 6125 transducers when dealing with cycle averaged data. This resulted in the development of a numerical thermal shock correction routine which was used for all subsequent data processing. Use of this improved analysis software demonstrated that the error in the calculated IMEP was significantly improved for the Ford Zetec engine tested. The range of Kistler 6123 IMEP errors were reduced from between -7% and -20% to between -1.5% and +1.4% after correction. Equivalent values for a Kistler 6125A transducer were -4.9% to -2.1% uncorrected down to between -0.4% and +0.8%.
Recommended Content
| Technical Paper | Spark advance for optimal efficiency |
| Technical Paper | The Accuracy of Calculating Wave Action in Engine Intake Manifolds |
| Technical Paper | Nonlinear Cylinder and Intake Manifold Pressure Observers for Engine Control and Diagnostics |
Authors
Citation
Rai, H., Brunt, M., and Loader, C., "Quantification and Reduction of IMEP Errors Resulting from Pressure Transducer Thermal Shock in an S.I. Engine," SAE Technical Paper 1999-01-1329, 1999, https://doi.org/10.4271/1999-01-1329.Also In
In-Cylinder Velocity Measurements, Combustion, and Flow Diagnostics
Number: SP-1446; Published: 1999-03-01
Number: SP-1446; Published: 1999-03-01
References
- Kuratle, R. H. Marki, B. “Influencing Parameters and Error Sources During on Internal Combustion Engines” SAE 920233 1992
- Randolph, A. L. “Cylinder-Pressure-Transducer Mounting Techniques to Maximise Data Accuracy” SAE 900171 1990
- Stein, R. A. Mencik, D. Z. Warren, C. C. “Effect of Thermal Strain on Measurement of Cylinder Pressure” SAE 870455 1987
- Kach, R. A. Adamczyk, A. A. “Effects of Thermal Loading on Pressure Measurement in a Combustion Bomb” Review of Scientific Instruments 56 6 June 1985
- Lancaster, D. R. Krieger, R. B. Lienesch, J. H. “Measurement and Analysis of Engine Pressure Data” SAE 750026 1975
- Brown, W. L. “Methods for Evaluating Requirements and Errors in Cylinder Pressure Measurements” SAE 670008 1967
- Randolph, A. L. “Methods of Processing Cylinder-Pressure Transducer Signals to Maximize Data Accuracy” SAE 900170 1990
- Puzinauskas, P. V. Eves, J. C. Tillman, N. F. “Measuring Absolute-Cylinder Pressure and Pressure Drop Across Intake Valves of Firing Engines” SAE 941881 1994
- Brunt, M. F. J. Emtage, A. L. “Evaluation of IMEP Routines and Analysis Errors” SAE 960609 1996
- Kistler Instruments Ltd. “Presentation of Kistler: Combustion Engine Measurement.” Kistler Publications September 1997
- Heywood, J. B. “ Internal Combustion Engine Fundamentals ” 0-07-100499-8