Results
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.00 inch (25.4 mm) and under in nominal thickness
This specification covers one type of copper in the form of wire (see 8.5
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness
This document specifies the on-board system requirements for vehicle-to-vehicle (V2V) safety system for school buses, including functional requirements and performance requirements. The system can send the SAE J2735-defined basic safety message (BSM) over a wireless communications interface; the communications interface itself is outside the scope of this document. This document provides the specifications necessary to build interoperable systems that support V2V applications that rely on receiving BSMs from school buses
This document provides the specifications of horizontal hard-bearing balancing machines, which make such machines suitable for gas turbine rotor balancing
This standard covers a single shielded balanced pair (twisted or parallel) jacketed data cable intended for use in surface vehicle cables for 2.5, 5, and 10 Gb/s Ethernet applications. The tests in this standard are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission
This specification covers a copper alloy (naval brass) in the form of bars and rods (see 8.5
This specification covers a low-alloy steel in the form of welding wire
This specification covers a cobalt-nickel-iron alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading
This SAE Standard specifies system requirements for an onboard vehicle-to-vehicle (V2V) safety communications system for vehicle classes of 2, 3, 4, and 51, including standards profiles, functional requirements, and performance requirements. The system is capable of transmitting and receiving the SAE J2735-defined basic safety message (BSM) over a PC5 Sidelink V2X (mode 4) communications link as defined in ETSI Release 142,3. The system uses Institute of Electrical and Electronics Engineers (IEEE) 1609 standards for network and transport layer communciations, as well as security
This specification covers a corrosion-resistant steel in the form of laminated sheet
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing (see 8.6
This specification covers a corrosion- and moderate heat-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness
This SAE Aerospace Standard (AS) covers the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace fuel and lubricating oil systems at temperatures between -67 °F and 450 °F and at operating pressures per Table 1. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems, where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this document, for example oxygen, shall be subject to the approval of the purchaser
This specification covers an aluminum bronze alloy in the form of sand castings (see 8.5
This specification covers one type of brass in the form of wire (see 8.5
This specification covers a low-alloy steel in the form of welding wire
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6
This specification covers an aluminum alloy in the form of clad sheet from 0.006 to 0.249 inches (0.15 to 6.32 mm), inclusive, in thickness (see 8.6
The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917
This specification establishes the requirements for etch inspection of steel parts to detect overheating (rehardening or over-tempering) caused by abusive machining or grinding or to detect localized discontinuous carburization
This specification covers the requirements for black oxide coatings on parts
The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917
This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles up to 0.499 inches (12.67 mm) in nominal diameter, or least thickness, and under 10 in2 (65 cm2) in cross-sectional area
This document defines cables that are used to provide electrical power for U.S. Department of Defense avionics support and test equipment
This SAE Aerospace Standard (AS) establishes the requirements for internally or externally swaged or welded sleeves or tube end adapters for use with 24° cone flareless fluid connection fittings per AS18280
This specification covers an aluminum alloy in the form of extruded profiles (shapes) 0.063 to 0.375 inch (1.6 to 10 mm), inclusive, in nominal thickness (see 8.6
This SAE Aerospace Information Report (AIR) considers the following major areas: 1 major components and their ratings; 2 selection criteria for optimum design balance for electrical systems; 3 effects of operating conditions and environment on both maintenance and life of components; 4 trouble signals - their diagnosis and cure
See Table 1
See Table 1
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.00 inch (25.4 mm) and under in nominal thickness
This specification covers a copper alloy (naval brass) in the form of bars and rods
This specification covers one type of brass in the form of wire
This specification covers one type of copper in the form of wire
This terminology is intended to provide a common nomenclature for use in publishing road vehicle aerodynamics data and reports
Items per page:
50
1 – 50 of 209362