Search
Advanced Search
of the following are true

Results

Items (208,215)
This specification covers pyrometric requirements for equipment used for the thermal processing of metallic materials. Specifically, it covers temperature sensors, instrumentation, thermal processing equipment, correction factors and instrument offsets, system accuracy tests, and temperature uniformity surveys. These are necessary to ensure that parts or raw materials are heat treated in accordance with the applicable specification(s
AMS B Finishes Processes and Fluids Committee
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet and strip up to 0.187 inch (4.75 mm) thick, inclusive, and plate up to 4.000 inches (101.6 mm) thick, inclusive
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a copper-nickel-tin alloy in the form of castings, made using the investment process unless sand or centrifugal processes are agreed upon by the purchaser (see 8.5
AMS D Nonferrous Alloys Committee
This SAE Aerospace Recommended Practice (ARP) provides a framework for establishing methods and stakeholder responsibilities to ensure that seats with integrated electronic components (e.g., actuation system, reading light, inflatable restraint, in-flight entertainment equipment, etc.) meet the seat technical standard order (TSO) minimum performance standards (MPS). These agreements will allow seat suppliers to build and ship TSO-approved seats with integrated electronic components. The document presents the roles and accountabilities of the electronics manufacturer (EM), the seat supplier, and the TC/ATC/STC applicant/holder in the context of AC 21-49, Section 7.b (“Type Certification Using TSO-Approved Seat with Electronic Components Defined in TSO Design”). This document applies to all FAA seat TSOs C39( ), C127( ), etc. The document defines the roles and responsibilities of each party involved in the procurement of electronics, their integration on a TSO-approved seat, and the
Aircraft Seat Committee
AS22759 specification covers fluoropolymer-insulated single conductor electrical wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable detail specification. The fluoropolymer insulation may be polytetrafluoroethylene (PTFE), fluorinated ethylene propylene (FEP), polyvinylidene fluoride (PVF2), ethylene-tetrafluoroethylene copolymer (ETFE), or other Fluoropolymer resin. The fluoropolymer may be used alone or in combination with other insulation materials. These abbreviations shall be used herein. When a wire is referenced herein, it means an insulated conductor (see 7.7
AE-8D Wire and Cable Committee
This specification covers a magnesium alloy in the form of sand castings
AMS D Nonferrous Alloys Committee
This SAE Aerospace Information Report (AIR) is a process verification guide for evaluating implementation of key factors in repair of fiber reinforced composite bonded parts or assemblies in a repair shop, hangar, or on-wing environment. This guide is to be used in conjunction with a regulatory approved and substantiated repair and is intended to promote consistency and reliability
AMS CACRC Commercial Aircraft Composite Repair Committee
The scope of this SAE Information Report is limited to a lift crane mounted on a fixed or floating platform, lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a workboat as defined in 3.15
Cranes and Lifting Devices Committee
This SAE Aerospace Recommended Practice (ARP) provides recommended use and installation procedures for bonded cable harness supports
AE-8A Elec Wiring and Fiber Optic Interconnect Sys Install
The scope of this SAE Recommended Practice is limited to cranes mounted on a fixed platform lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a work boat as defined in 3.14
Cranes and Lifting Devices Committee
ARINC 858 Part 2 provides aviation ground system gateway considerations necessary to transition to the Internet Protocol Suite (IPS). ARINC 858 Part 2 describes the principles of operation for an IPS gateway that enables ACARS application messages to be exchanged between an IPS aircraft and a ground ACARS host. ARINC 858 Part 2 also describes the principles of operation for an IPS gateway that enables OSI-based application messages to be exchanged between an IPS host and an OSI end system. This product was developed in coordination with ICAO WG-I, RTCA SC-223, and EUROCAE WG-108
Airlines Electronic Engineering Committee
This index provides an overview of lubricants and symbols for the purpose of assisting the user in the identification of the appropriate product and relevant SAE specification. The aim is to better determine the best lubricant to be used for a particular application. If containers used for shipping lubricants are also to be marked, the same identification and symbols should be used. See also ISO 5169 Machine tools - Presentation of lubrication instructions
Fuel and Lubricants TC2 Industrial Lubricants
The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917
Marine Technical Steering Committee
See Table 1. DAx fluids are mineral oil based, DPx fluids are polyalphaolefin based, and DEx are ester based
Fuel and Lubricants TC2 Industrial Lubricants
ISO 7745 shall be used for providing detailing, operational characteristics, advantages, disadvantages, and factors affecting the choice to be made among fire-resistant fluids. HFAE, HFC, HFDR, HFDU and HETG oils are covered in this specification. HFAS, HFB and HFDS fluids are not addressed
Fuel and Lubricants TC2 Industrial Lubricants
This specification defines the requirements for in-process correction of foundry discontinuities by manual welding of castings
AMS B Finishes Processes and Fluids Committee
This SAE Aerospace Recommended Practice (ARP) addresses the general procedure for the best practices for minimizing uncertainty when calibrating thermal conductivity and cold cathode vacuum gauges, which includes the vacuum sensor(s) and accompanying electronics necessary for a pressure measurement to be made. It also includes the best practices for an in-process verification where limitations make it impossible to follow the best practices for minimizing uncertainty. Verifying the accuracy and operation of vacuum gauges is critical to ensure the maintenance of processes while under vacuum
AMS B Finishes Processes and Fluids Committee
This SAE Aerospace Recommended Practice defines a method for determining the weldability of weld filler metal in continuous coil or cut length form. It is applicable to all solid (non flux-containing) wires. It is intended as a referee method for testing weld filler metals in case of dispute between purchaser and vendor
AMS B Finishes Processes and Fluids Committee
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the exterior sound level for passenger cars, multipurpose vehicles, and light trucks having a gross vehicle mass rating of 4540 kg or less. The test procedure is characterized by having fixed initial conditions, i.e., an as-specified initial vehicle speed and gear selection at a fixed start point on the test site. Full-throttle acceleration and closed-throttle deceleration of the vehicle are included in this procedure. Sound levels determined in accordance with this document are dependent on the performance capability of the test vehicle, as influenced by power-to-mass ratio and overall powertrain gear ratio
Light Vehicle Exterior Sound Level Standards Committee
This specification covers engineering requirements for the grinding of tungsten carbide high velocity oxygen/fuel (HVOF) thermal spray coatings applied to high strength steels (220 ksi and above
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for vacuum deposited cadmium
AMS B Finishes Processes and Fluids Committee
This specification establishes the requirements for a chemical conversion coating on titanium alloys
AMS B Finishes Processes and Fluids Committee
This specification establishes the engineering requirements for producing an acid-type, anodic coating on magnesium alloys and the properties of the coating
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for ion vapor deposited (IVD) aluminum on steel, titanium, and aluminum alloys
AMS B Finishes Processes and Fluids Committee
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met
SAE IC Powertrain Steering Committee
Illustrations used here are not intended to include all existing industrial or agricultural machines, or to be exactly descriptive of any particular machine. They have been picked to describe the principles to be used in applying this standard
OPTC1, Personnel Protection (General)
This specification establishes the requirements for a hard anodic coating on aluminum and aluminum alloys
AMS B Finishes Processes and Fluids Committee
This specification establishes the engineering requirements for producing an acid-type, anodic coating on magnesium alloys and the properties of the coating
AMS B Finishes Processes and Fluids Committee
This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for producing brazed joints on aluminum and aluminum alloys by torch or furnace brazing
AMS B Finishes Processes and Fluids Committee
This specification covers the engineering requirements for electrodeposition of a hard nickel and the properties of the deposit
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for producing brazed joints using copper as the brazing filler metal
AMS B Finishes Processes and Fluids Committee
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test strip holder is required for intensity determination
AMS B Finishes Processes and Fluids Committee
This specification covers requirements for electrodeposited porous chromium plate
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for electrodeposited cadmium plating
AMS B Finishes Processes and Fluids Committee
An enormous economic loss, as well as a waste of natural resources, is incurred world-wide as a result of wear of components and tools. Any effort expended in an attempt to reduce this loss is indeed worthwhile. The purpose of this SAE Information Report is to present the current state of knowledge of abrasive wear. This report, therefore, covers wear, or the undesired removal of metal by mechanical action, caused by abrasive particles in contact with the surface. It does not concern metal-to-metal wear or wear in the presence of an abrasive free lubricant. Abrasive wear occurs when hard particles, such as rocks, sand, or fragments of certain hard metals, slide or roll under pressure across a surface. This action tends to cut grooves across the metal surface, much like a cutting tool. Abrasive wear is of considerable importance in any part moving in relation to an abrasive. Tools in contact with the ground, such as plows, cultivators, scraper and bulldozer blades, are intended to
Metals Technical Committee
This specification covers the requirements for thin, hard, dense electrodeposited chromium plating on surfaces of ferrous and nonferrous alloys
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for electrodeposited nanocrystalline cobalt-phosphorus plating
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for electrodeposited copper
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for brush plating of hard chromium by electrodeposition
AMS B Finishes Processes and Fluids Committee
This specification covers the engineering requirements for finishing aircraft parts and assemblies with a black enamel
AMS B Finishes Processes and Fluids Committee
Items per page:
1 – 50 of 208215