Results
This SAE Recommended Practice establishes recommended procedures for the issuance, assignment, and structure of Identification Numbers on a uniform basis by states or provinces for use in an Assigned Identification Number (AIN).
This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connectors, direct wire wedge base sockets, bayonet base sockets with integral connectors, direct wire bayonet base sockets, wedge base and bayonet base sockets with circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendices E and F whenever the following occurs: New design. Design, material, or process change made to an existing device, which could affect the outcome of the test. The test sequences shown in Appendix G shall be run annually.
This document describes the design relative to assembly force, and hand clearance guidelines for conventional hand-plug, mechanical assist and twist lock electrical connectors, as well as Connector Position Assurances (CPAs). The minimum values associated with this design guide need to be evaluated against other critical characteristics that impact quality, efficiency and other traits of assembly feasibility. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the-shelf” design, always consult the responsible Ergonomics Department.
This specification covers the grain flow pattern requirements in headed bolts, screws, and studs. The heading practice in the manufacture of the bolt, screw, or stud sets the grain flow pattern, but it is also greatly influenced by the fastener and tooling design as well as cold-forging setup. The use of tooling design simulation software is recommended and a commonly used practice that provides reliable forging predictions for superior grain flow quality.
This standard outlines the conditions that enhance the risk of hydrogen embrittlement of steel and define the relief procedures required to minimize the risk of hydrogen embrittlement. It is intended to control the process.
This International Standard specifies the dimensions, test methods, and requirements for single core 60 V cables intended for use in road vehicle applications where the nominal system voltage is ≤ (60 V DC or 25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is > (60 V DC or 25 V AC) to ≤ (600 V DC or 600 V AC). It also applies to individual cores in multi-core cables. See ISO 6722 for “Temperature Class Ratings”.
This SAE Recommended Practice applies to nomenclature of emissions and emissions reduction apparatus as applied to various engines and vehicles. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding.
To measure the performance characteristics of Continuously Variable Transmissions (CVT). It outlines dynamometer tests that cover the range of operation and provides a method of presenting the test data. This procedure must be followed with similar test facilities so that results obtained from different laboratories are comparable.
This SAE Information Report contains definitions for hydrogen fuel cell powered vehicle terminology. It is intended that this document be a resource for those writing other hydrogen fuel cell vehicle documents, specifically, Standards or Recommended Practices.
This information applies to refrigerant used to service automobiles, light trucks, and other vehicles with similar CFC-12 (R-12) systems. Systems used on mobile vehicles for refrigerated cargo that have hermetically sealed, rigid pipe, are not covered in this document.
The test procedures and performance criteria are directed to operation and parking of agricultural tractors equipped with braking system(s) and having a maximum design speed exceeding 6 km/h. Combinations of agricultural towing machines equipped with braking systems and towed agricultural machines without braking systems are included in this SAE Standard.
Minimum performance criteria for service braking systems, emergency stopping systems, and parking systems for off-highway, rubber-tired, self-propelled loaders, dumpers, tractor scrapers, graders, cranes, excavators, and tractors with dozer are provided in this SAE Recommended Practice. Refer to SAE J1057 (July, 1973) and J1116 (July, 1975) (Sections 1.1, 1.2, and 2) for machine identification.
This SAE Recommended Practice is intended to outline basic nomenclature for axle designs in common use for automotive drives. Over a period of years, there have been many different designs; however, for the purpose of this report, only the most common designs have been selected and only their general construction is illustrated to show the nomenclature of the various parts.
This SAE Recommended Practice describes the equipment and procedure for determining the truck cab interior sound level over the upper half of the engine speed range. This practice applies to motor trucks and truck-tractors and does not include construction and industrial machinery.
The guidelines in this SAE Information Report are directed at laboratory engine dynamometer test procedures with alternative fuels, and they are applicable to four-stroke and two-stroke cycle spark ignition (SI) and diesel (CI) engines (naturally aspirated or pressure charged, with or without charge air cooling). A brief overview of investigations with some alternative fuels can be found in SAE J1297. Other SAE documents covering vehicle, engine, or component testing may be affected by use of alternative fuels. Some of the documents that may be affected can be found in Appendix A. Guidelines are provided for the engine power test code (SAE J1349) in Appendix D. The principles of these guidelines may apply to other procedures and codes, but the effects have not been investigated. The report is organized into four technical sections, each dealing with an important aspect of testing or reporting of results when using alternative fuels. The first (Section 3) deals with such issues as what
Mercury capsules have been used in the automotive industry in various switching applications. The basic design and performance characteristics of mercury switches (or capsules) make these components particularly suited to underhood light and trunk light applications. The processes described in this SAE Standard deal with the location, removal, storage, and recycling of mercury switches and capsules associated with these underhood and trunk light applications.
This SAE Recommended Practice applies to all forms of diesel and natural gas engines fueled by the combination of diesel fuel and natural gas.
This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report. Because this is an Information Report, the numerical values for performance measurements presented in this report and
Items per page:
50
1 – 50 of 212795