This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
BOLT, MACHINE-SPLINE DRIVE HEAD, DRILLED, PD SHANK-LONG THREAD, AMS6322, CADMIUM PLATED, METRIC
- Aerospace Standard
- MA3367A
- Reaf. Nonc.
Sector:
Issuing Committee:
Language:
English
Rationale
THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY.
-
1
FOR PARTS WHERE DIMENSION N IS EQUAL TO OR LESS THAN ONE DIAMETER, REPLACE DATUM WITH .
-
2
MATERIAL: LOW-ALLOY STEEL AMS6322.
-
3
PROCUREMENT SPECIFICATION: MA3376
-
4
HARDNESS: 26-32 HRC OR EQUIVALENT.
-
5
FINISH: CADMIUM PLATE PER AMS2400. DIMENSIONS ARE AFTER PLATING.
-
6
MAGNETIC PARTICLE INSPECTION: AMS2640
-
7
SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36-1978; REQUIREMENTS PER ANSI B46.1-1985. UNLESS OTHERWISE SPECIFIED SURFACES TO BE 3.2 MICROMETERS Ra.
-
8
PART NUMBER SHALL INCLUDE THE STANDARD NUMBER AND THE DASH NUMBER TO INDICATE DIAMETER AND LENGTH. EXAMPLE OF PART NUMBER:
-
9
SHAPE OF BOTTOM OF HOLE MAY BE FLAT OR CURVED WITHIN DIMENSIONS SHOWN. NO HOLE IS REQUIRED ON DIAMETER 4.
-
10
WRENCHING CONFIGURATION SHALL BE IN ACCORDANCE WITH MA1549. FOR THE APPLICABLE DASH NUMBER SEE TABLE I.
-
11
BREAK EDGES 0.1-0.4, UNLESS OTHERWISE SPECIFIED.
-
12
DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. TOLERANCE GRADES PER ANSI B4.2-1978.
-
13
ALL DIMENSIONS IN SI MILLIMETRES UNLESS OTHERWISE SPECIFIED.
-
14
DO NOT USE UNASSIGNED PART NUMBERS.
-
15
AFTER OCTOBER 1996 PARTS ARE CADMIUM PLATED.
Topic
Data Sets - Support Documents
No Datasets Available
Issuing Committee
E-25 General Standards for Aerospace and Propulsion Systems
The SAE E-25 General Standards for Aerospace & Propulsion Systems committee addresses aerospace propulsion systems and components. These systems and components include bolts, screws, nuts, washers, studs, rivets, pins, covers, O-rings, brackets, plugs and associated procurement requirements, as well as solid film lubricants and design specifications for screw threads and fastener assembly requirements.
Reference
Number | Title |
---|---|
AMS2400 | PLATING, CADMIUM |
AMS2640 | Magnetic Particle Inspection |
ANSI/ASME/B 46.1M | This document is not part of the subscrption. |
ANSI/ASME/B46.1 | This document is not part of the subscrption. |
ANSI/B4.2 | This document is not part of the subscrption. |
ANSI/Y14.36 | This document is not part of the subscrption. |
ANSI/Y14.5M | This document is not part of the subscrption. |
MA1549 | Wrenching Configuration, 12 Spline, For Metric Threaded Fasteners |
MA3376 | BOLTS & SCREWS, SAE 8740 HEAT TREATED, ROLL THREADED PROCUREMENT SPECIFICATION FOR, METRIC |
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.