This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Some Techniques to Improve Performance of Si Engine At Part Loads - A Numerical and Experimental Approach
Technical Paper
2003-28-0026
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Work in this paper involves the computer simulation and experimental investigations on a single-cylinder, four-stroke, spark-ignition engine in which inlet valve closure timing and clearance volume are optimized for better part -load performance. The simulation procedure involves thermodynamic and global modeling techniques. Many sub-models have been used for predicting heat transfer, friction and gas exchange processes. A two-zone model is adopted for combustion process. The combustion model used here predicts mass burning rates, ignition delay and combustion duration, etc. Sub-models for calculating flame-front area, flame -speed and chemical equilibrium composition of ten product species are used in combustion analysis. Measured valve -displacement along with suitable coefficient of discharge is used in the analysis of gas exchange processes. Unburned hydrocarbons and carbon monoxide emissions have been predicted.
Experiments have been conducted on a modified single-cylinder, air-cooled, four-stroke, spark-ignition engine. A standard diesel engine was modified to carryout the experiments. Late intake valve closure (LIVC) associated with variable compression ratio (VCR) concepts have been used in the modified engine. Clearance volume was altered suitably to achieve variable compression ratio. In this work, geometric expansion ratio (GER) of modified alone is varied, while effective compression ratio (ECR) is kept constant, thereby GER/ECR ratio is altered. For modified engine, GER/ECR ratio was varied from 1.25 to 2. Experiments were conducted for two effective compression ratios, viz. 7 and 8 at a speed of 1200 rpm. Performance and exhaust emissions have been measured at different loads and GER/ECR ratios. The pre dicted performance and emission characteristics are compared with measured values and the agreement between the two is found to be good.
From the present investigations, it is concluded that, this concept is a viable one and the simulation software developed in this work predicts the performance and emission characteristics of modified engine quite well. Therefore, it is argued that the developed code can be used with confidence for further parametric studies and to optimize the GER/GCR ratio for the given engine configuration for practical applications.
Authors
Topic
Citation
Mallikarjunappa, J. and Ganesan, V., "Some Techniques to Improve Performance of Si Engine At Part Loads - A Numerical and Experimental Approach," SAE Technical Paper 2003-28-0026, 2003, https://doi.org/10.4271/2003-28-0026.Also In
References
- Mallikarjuna, J. M. Numerical and Experimental Studies on Single Cylinder Four-Stroke Spark-Ignited Extended Expansion Engine IIT Madras 1998
- Mallikarjuna, J. M Ganesan V. 1998 The Performance Characteristics of Extended Expansion Four-Stroke Spark-Ignited Engine - Numerical Predictions and Experimental Comparisons Institution of Engineers (India) Journal-MC 79 128 133 November
- Nagesh, M.S. Mallan K.R. Govinda Gopalakrishnan K.V. 1992 Experimental Investigations on Extended Expansion Engine (EEE) SAE Paper 920452
- Mallikarjuna, J. M Ganesan V. Theoretical and Experimental Investigations of Extended Expansion Concept for SI Engines SAE paper 2002-01-1740 2002
- Nazar, J. Gopalakrishnan K.V. Mavinahally Nagesh.S. 1997 Naturally Aspirated Low Heat Rejection Single Cylinder Extended Expansion (Miller Cycle) C.I. Engine SAE Paper 970202
- Nagesh, M.S. Experimental Investigations on Extended Expansion Concept Applied to a Four-Stroke SI Engine IIT, Madras 1991
- Nagesh, M.S. Mallan K.R. Govinda Gopalakrishnan K.R. 1989 Extended Expansion Engine Concept for Better Thermal Efficiency XI National Conference on I.C. Engines and Combustion IIT, Madras
- Ramos, J.I. Internal Combustion Engine Modeling Hemisphere Publishing Corporation 1989
- Ganesan, V. Computer Simulation of Spark-Ignition Engine Processes University Press (India) Ltd. 1996
- Campbell, A.S. Thermodynamic Analysis of combustion Engines John Wiley and Sons New York 1979
- Heywood, J.B. Internal Combustion Engines Fundamentals McGraw Hill Book Company 1988
- Benson, R.S. The Thermodynamics and Gas Dynamics of Internal Combustion Engines, I Horlock, J.K. Winterborne D.E. Clarendon Press Oxford 1982
- Horlock, J.H. Winterborne D.E. The Thermodynamics and Gas Dynamics of Internal Combustion Engines, II Oxford University Press 1986
- Blizard, N.C. Keck J.C. 1974 Experimental and Theoretical Investigation of Turbulent Burning Model for Internal Combustion Engines SAE Paper 740191
- Tabaczynski, R.J. Ferguson C.R. 1977 A Turbulent Entrainment Model for Spark-Ignition Combustion SAE Paper 770647
- Kuo, K.K. Principles of Combustion Wiley Interscience 1986
- Woschni, G. 1967 A Universally Applicable Equation for the Instantaneous Heat Transfer Coefficient in the Internal Combustion Engines SAE Paper 670931 64 3065 3083
- Bishop, I.N. 1964 Effect of Design Variables on Friction and Economy SAE Paper 812-A 3 27
- Charles, E.S. 1966 Combustion Chamber Surface Area a Key to Exhaust Hydrocarbons SAE Paper 660111
- David, W.A. 1955 Flame Quenching at the Walls of an Internal Combustion Engines Sixth International Symposium on Combustion 886 894
- Korematsu Koji “Effect of fuel absorbed in oil film on unburnt hydro carbon emissions from spark ignition engine (Numerical model for dynamic processes of fuel absorption and desorption)” JSME international journal, series II 33 3 1990 606 614
- Davis, G.C Borgnakke C. 1982 The Effect of In-Cylinder Flow Processes (Swirl, Squish and Turbulence Intensity) on Engine Efficiency - Model Predictions SAE Paper 820045
- Poulos, S.G. Heywood J.B. 1983 The effect of chamber Geometry on Spark-Ignition Engine Combustion SAE Paper 830334
- Ma, T.H. 1988 Effect of Variable Engine Valve Timing on Fuel Economy SAE Paper 880390
- Ma, T.H. Rajabu H. 1988 Computer Simulation of Otto-Atkinson Cycle Engine with Variable Timing Multi-Intake Valves and Variable Compression Ratio I.Mech.E, C53/88 273 277
- Luria, D. Taitel Y. Stotter A. 1982 The Otto-Atkinson Engine -A New Concept in Automotive Economy SAE Paper 820352
- Ladommotos, M. Balian R.A. 1990 Combustion in a Direct Injection Diesel Engine with Increased Clearance Volume Proceeding of I.Mech.E., Journal of Automobile Eng. 204 187 197
- Felt, A.E. Krause S.R. 1971 Effect of Compression Ratio Changes on Exhaust Emissions SAE Paper 710831
- Daniel, W.A. Wentworth J.T. 1964 Exhaust Gas Hydrocarbons - Genesis and Exodus, Vehicle Emissions SAE Technical Progress Series 6
- Siewert, R.M. 1971 How Individual Valve Timing Events Affect Exhaust Emissions SAE Paper 720052
- Hara Seinosuke Hidaka Akira Tomisawa Naoki Nakamura Makoto Todo Tamotsu Takemura Shinichi Nohara Tsuneyasu 2000 “Application of a Variable Valve Event and Timing System to Automotive Engines” SAE Paper 2000-01-1224 , SP-1523
- Flierl Rudolf Kluting Manfred 2000 “The Third Generation of Valvetrains - A New Fully Variable Valvetrains for Throttle-Free Load Control” SAE Paper 2000-01-1227 , SP-1523
- Pierik Ronald J. Burkhard James F 2000 “Design and Development of a Mechanical Variable Valve Actuation System” SAE Paper 2000-01-1221 , SP-1523
- Hannibal, W 1998 “VAST: A New Variable Valve Timing System for Vehicle-Engines” SAE Paper 980769 , SP-1346