This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Simulation Model for Gasoline Engine Cold Start Fuel Calibration
Technical Paper
2002-01-2802
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
The paper presents a simulation model for the cold start fuel calibration (CSFC) in port-fuel-injected gasoline engines. The model is based on data that is readily available during regular engine tests. The model has been applied to a 2.4L, 4-cylinder, 16 valve, DOHC, multipoint-port-fuel-injection spark ignition gasoline engine. The model determines the amount of fuel vaporized in the intake port at any crank angle degree, and in the cylinder on cycle-by-cycle basis, during the cold start process.
Recommended Content
Topic
Citation
Luan, Y. and Henein, N., "A Simulation Model for Gasoline Engine Cold Start Fuel Calibration," SAE Technical Paper 2002-01-2802, 2002, https://doi.org/10.4271/2002-01-2802.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 |
Also In
References
- Becker E. R. Watson R. J. “Future Trends in Automotive Emission Control,” SAE Paper 980413 1998
- Luan Y. Henein N. A. “Contribution of Cold and Hot Start Transients in Engine-out HC Emissions,” SAE Paper 982645 1998
- Henein N. A. Tagomori M. K. Yassine M. K. Asmus T. W. Thomas C. P. Hartman P. G. “Cycle-By-Cycle Analysis of HC Emissions During Cold Start of Gasoline Engines,” SAE Paper 952402 1995
- Quader A. A. “Single-Cylinder Engine Facility to Study Cold Starting - Results with Propane and Gasoline,” SAE Paper 920001 1992
- Quader A. A. Majkowski R. F. “Cycle-by-Cycle Mixture Strength and Residual-Gas Measurements During Cold Starting,” SAE Paper 1999-01-1107 1999
- Takeda K. Yaegashi T. Sekiguchi K. Saito K. Imatake N. “Mixture preparation and HC Emissions of a 4-Valve Engine with Port Fuel Injection During Cold Starting and Warm-up,” SAE Paper 950074 1995
- Shayler P. J. Colechin M. J. F. Scarisbrick A. “Fuel Film Evaporation and Heat Transfer in the Intake Port of an S.I. Engine,” SAE Paper 961120 1996
- Coste T. L. Evers L. W. “An Optical Sensor for Measuring Fuel Film Dynamics of a Port-Injected Engine,” SAE Paper 970869 1997
- Meyer R. Heywood J. B. “Effect of Engine and Fuel Variables on Liquid Fuel Transport into the Cylinder in Port-Injected SI Engines,” SAE Paper 1999-01-0563
- Aquino C. F. “Transient A/F Control Characteristics of the 5 Liter Central Fuel Injection Engine,” SAE Paper 810494 1981
- Hires S. D. Overington M. T. “Transient Mixture Strength Excursion - An Investigation of Their Causes and the Development of a Constant Mixture Strength Fueling Strategy,” SAE Paper, 810495
- Shayler P. J. Teo Y. C. Scarisbrick A. “Fuel Transport Characteristics of Spark Ignition Engines for Transient Fuel Compensation,” SAE Paper 950067 1995
- Shayler P. J. Sage J. D. Dixon J. Eade D. “Computer Aided Evaluation of Cold Start Fueling Strategy and Calibration Details for Spark Ignition Engines,” SAE Paper 940085 1994
- Shayler P. J. Belton C. Scarisbrick A. “Emissions and Fuel Utilisation after Cold Starting Spark Ignition Engines,” SAE Paper 1999-01-0220 1999
- Horie K. Takahasi H. Shusuke A. “Emissions Reduction During Warm-Up Period by Incorporating a Wall-Wetting Fuel Model on the Fuel Injection Strategy During Engine Starting,” SAE Paper 952478 1995
- Habib I. S. “Fuel Droplets Evaporation in Moving Gaseous Medium,” Int. J. Heat Transfer 13 1382 1386 1970
- Brown C. N. Ladommatos N. “A numerical Study of Fuel Evaporation and Transportation in the Intake Manifold of a Port-injected Spark-Ignition Engine,” Proc. IMechE 205 161 175 1991
- Abramzon B. Sirignano W. A. “Droplet vaporisation model for Spray Combustion Calculation,” Int. J. Heat Mass Transfer 1605 1617 1989
- Schurov S. M. Collings N. “A Numerical Simulation of Intake Port Phenomena in a Spark Ignition Engine Under Cold Starting Conditions,” SAE Paper 941874 1994
- Incropera F. P. DeWitt D. P. Fundamentals of Heat and Mass Transfer,” 3rd John Wiley & Sons 1990
- Curtis E. W. Aquino C. F. Trumpy D. K. Davis G. C. “A New Port and Cylinder Wall Wetting Model to Predict Transient Air/Fuel Excursions in a Port Fuel Injected Engine,” SAE Paper 961186 1996
- Van Wylen G. J. Sonntag R. E. “Fundamentals of Classical Thermodynamics,” John Wiley & Sons, Inc. 1965
- Cheng C. Cheng W. K. Heywood J. B. Maroteaux D. Collings N. “Intake Port Phenomena in a Spark-Ignition Engine at Part Load,” SAE Paper 912401 1991
- Badillo E. Assanis D. N. Servati Hamid “One-Dimensional Transient Dynamics of Fuel Evaporation and Diffusion in Induction Systems,” SAE Paper 970058 1997
- Bird R. B. Stewart W. E. Lightfoot E. N. “Transport Phenomena,” Wiley New York 1960