This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
User's Manual for the Small Adult Female Hybrid III Test Dummy
- Ground Vehicle Standard
- J2862_201502
- Issued
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
This user’s manual covers the small adult female Hybrid III test dummy. It is intended for technicians who work with this device. It covers the construction and clothing, disassembly and reassembly, available instrumentation, external dimensions and segment masses, as well as certification and inspection test procedures. It includes instructions for safe handling of the instrumented dummy, repairing dummy flesh, and adjusting the joints throughout the dummy.
Rationale
SAE J2862 replaced EA-25 in 2015. In addition to the format change and the correction of typographical and grammatical errors, the following changes were made to this Information Report:
-
References to SAE J211 were changed to J211-1 throughout the report
-
Joint adjustment changed from “1 – 2 G” to “1 G suspended adjustment” throughout the report
-
Section 1 SCOPE – added
-
Section 2 REFERENCES – added “SAE J211-1 – Instrumentation for Impact Test – Part 1 – Electronic Instrumentation”
-
Section 2 REFERENCES – added “SAE J2517 – Hybrid III Family Chest Potentiometer Calibration”
-
Section 2 REFERENCES – added “SAE J2878 – Low Speed Thorax Impact Test Procedure for the HIII 5th Dummy”
-
Section 2 REFERENCES – added “SAE J2915 – H-III5F Spine Box Update to Eliminate Noise”
-
Section 2 REFERENCES – added “SAE J2921 – H-III5F Chest Jacket Harmonization”
-
Section 2 REFERENCES – added “Banglmaier, R.F., Pecararo, K.M., Feustel, J.R., Scherer, R.D. and Rouhana, S.W., 2005, “Development and evaluation of a Proposed Neck Shield for a 5th Percentile Hybrid III Dummy,” Stapp Car Crash Journal, vol. 49.”
-
Section 3 DEFINITIONS AND ABBREVIATIONS and throughout the document – changed “Calibration Test” to “Certification Test” for all tests that are conducted for the purpose of assuring that the dummy responds within the specifications outlined in this document
-
Section 4 PART NUMBERS – updated source for 49 CFR, Part 572, Subpart O drawings
-
Section 7 DISASSEMBLY AND REASSEMBLY PROCEDURES – added “TABLE 1 – TORQUE SPECIFICATIONS” and indexed all other table numbers accordingly.
-
Section 7 DISASSEMBLY AND REASSEMBLY PROCEDURES – changed “sternum bib” to “bib assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.3 Head – corrected the part number of the head skin
-
Section 7.4 Neck – changed the description of part number 180-2004 from “neck cable insert, upper” to “neck bushing, upper” and changed the description of part number 180-2005 from “neck cable insert, lower” to “neck bushing, lower” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.4 Neck – changed the description of part number 880105-255 from “molded rubber neck” to “neck molded assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – changed the description of part number 880105-1000 from “spine weldment” to “thoracic spine weldment” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – changed the description of part number 880105-323 from “behind rib strips” to “front rib end, threaded” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – changed the description of part number 880105-324 from “stiffener strip” to “front rib end stiffener” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – changed the description of part number 880105-340 from “nut” to “clavicle link pivot nut” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – changed the description of part number 880105-342 from “clavicle link washer” to “”clavicle link pivot washer (Delrin)” for consistency with the NHTSA PADI, dated June 10, 2002
-
Section 7.5 Upper Torso – changed the description of part number 880105-359 from “washer sternum” to “”clavicle link pivot washer (Urethane)”for consistency with the NHTSA PADI, dated June 10, 2002
-
Section 7.5 Upper Torso – changed the description of part numbers 880105-380[left], -381[right] from “shoulders” to “shoulder assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – corrected the part number of the rib set
-
Section 7.5 Upper Torso – changed the description of part number 880105-1085 from “adaptor assembly” to “adaptor assembly lumbar thoracic” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5 Upper Torso – changed the description of part number 8801205-1080 from “chest transducer assembly” to “chest deflection transducer assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.5.1 Upper Torso Disassembly – changed “one G adjustment” to “1 G suspended setting”
-
Section 7.5.2 Upper Torso Reassembly – added directions to re-tighten the SHCS to eliminate mechanical noise caused by slippage between the spine mounting assembly and the load cell simulator
-
Section 7.6 Chest Deflection Transducer – corrected the part numbers of the molded stop assembly, chest accelerometer mount, and chest potentiometer for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.6 Chest Deflection Transducer – changed the description of part number 880105-328 from “thoracic spine load cell structural replacement” to “thoracic spine load cell simulator” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.6 Chest Deflection Transducer – changed the description of part number SA572-S51 from “potentiometer” to “chest potentiometer” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.6.1 Chest Deflection Transducer Disassembly – Added “Once calibrated according to J2715, “Hybrid III Family Chest Potentiometer Calibration Procedure” the chest potentiometer assembly consisting of the transducer arm assembly (Item 5, Figure 13), chest potentiometer (Item 12, Figure 13), potentiometer bracket (Item 13, Figure 13) and arm connector (Item 14, Figure 13) should not be mechanically adjusted or further disassembled.”
-
Section 7.7 Clavicle – changed description of part number 880105-344 from “shoulder pivot stop assembly” to “rubber stop assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.7 Clavicle – changed description of part number 880105-348 from “shoulder bushing” to “shoulder yoke pivot bushing” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.7 Clavicle – changed description of part number 880105-349 from “yoke pivot washer” to “shoulder yoke pivot washer” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.7 Clavicle – changed description of part number 880105-367 from “flat washer” to “clavicle link washer” for consistency with the NHTSA PADI, dated June 10, 2002
-
Section 7.7 Clavicle – changed description of part number 880105-351 from “spring washer” to “shoulder joint spring washer” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.7 Clavicle – changed description of part number 880105-357 from “link bushing” to “clavicle and clavicle link bushing” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.8 Lower Torso – changed the description of part number 880105-440 from “pelvic molded assembly” to “molded pelvic assembly” for consistency with the NHTSA PADI, dated June 10, 2002
-
Section 7.8 Lower Torso – changed the description of part number 880105-404 from “spine cable” to “lumbar spine cable” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.8 Lower Torso – changed the description of part number 1200056 from “accelerometer mount” to “pelvic accelerometer mount” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.8 Lower Torso – corrected the part number of the femur bumper
-
Section 7.8 Lower Torso – Figure 20 number and caption were added. All subsequent figures were indexed by one number.
-
Section 7.9 Arms – changed the description of part number 880105-351 from “washer” to “shoulder joint spring washer” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-700 from “upper arm molded” to “upper arm molded assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-705 from “upper arm lower part” to “upper arm, lower part weldment” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-708 from “washer” to “upper arm and elbow pivot washer” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-709 from “bushing” to “upper arm and elbow pivot bushing” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-711 from “washer” to “upper arm pivot washer” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-718 from “wrist rotation” to “wrist rotation assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-712 from “lower arm molded” to “lower arm molded assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part number 880105-710 from “nut” to “upper arm pivot nut” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.9 Arms – changed the description of part numbers 880105-722[left] and 880105-723[right] from “hand” to “hand molded assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.10 Legs – changed the description of part number 880105-622 from “knee clevis” to “knee clevis weld assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.10 Legs – changed the description of part number A-1887 from “bolt” to “ankle to leg attachment bolt” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.10 Legs – changed the description of part number 880105-660 from “ankle” to “ankle assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.10 Legs – changed the description of part numbers 880105-502 [left] and 880105-503 [right] from “upper leg structural” to “upper leg weldment” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.10 Legs – changed the description of part number 78051-391 from “load cell replacement” to “femur load cell simulator” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.10 Legs – changed the description of part number 880105-631 from “ankle bumper” to “ankle bumper assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.11 Lower Legs – changed the description of part number 880105-622 from “knee clevis” to “knee clevis weld assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.11 Lower Legs – changed the description of part numbers 880105-650 [left] and 880105-651 [right] from “foot” to “foot assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.11 Lower Legs – changed the description of part number 880105-660 from “ankle” to “ankle assembly” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.11 Lower Legs – changed the description of part number 880105-527 from “shoulder screw” to “shoulder bolt, sliding knee” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.11 Lower Legs – changed the description of part number 880105-511 from “knee insert” to “knee flesh insert” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.13 Ankle and Foot – changed the description of part number 880105-609 from “upper shell” to “ankle, upper shell” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.13 Ankle and Foot – changed the description of part number 880105-633 from “lower shell” to “ankle, lower shell” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.13 Ankle and Foot – changed the description of part numbers 880105-652 [left] and 880105-653 [right] from “foot weldment” to “foot bone weldment” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 7.13 Ankle and Foot – changed the description of part number A-1887 from “bolt” to “ankle to leg attachment bolt” for consistency with 49 CFR, Part 572, Subpart O parts list
-
Section 8.1 Head Drop Test – added metric equivalent of surface finish to paragraph (C) for consistency with 49 CFR, Part 572, Subpart O, §572.132 (c) (4)
-
Section 8.1 Head Drop Test – added one significant digit to the drop height and tolerance in paragraph (E)(6) for consistency with 49 CFR, Part 572, Subpart O, §572.132 (c) (3)
-
Section 8.1 Head Drop Test (F)(3) – added “zero to peak” for consistency with 49 CFR, Part 572, Subpart O, §572.132 (b)
-
Section 8.2 Neck Tests (D)(7) – added one significant digit to the English equivalent of the jam nut torque for consistency with 49 CFR, Part 572, Subpart O, §572.133 (c) (2)
-
Section 8.2 Neck Tests (E)(1) – added “at the instant of contact with the honeycomb” consistency with 49 CFR, Part 572, Subpart O, §572.133(c) (4)(i)
-
Section 8.2 Neck Tests (E)(4) – changed the English equivalent of the positive moment decay for consistency with 49 CFR, Part 572, Subpart O, §572.133 (b) (1)
-
Section 8.2 Neck Tests (F)(1) – added “at the instant of contact with the honeycomb” for consistency with 49 CFR, Part 572, Subpart O, §572.133(c) (4)(i)
-
Section 8.2 Neck Tests (F)(4) – changed performance specifications for peak moment and the English equivalents of the positive moment decay for consistency with 49 CFR, Part 572, Subpart O, §572.133 (c) (2)
-
Section 8.2 Neck Tests (F)(5) – changed the performance specification for the maximum rotation of the D-plane for consistency with 49 CFR, Part 572, Subpart O, §572.133 (b) (2)
-
Section 8.3 Thorax Impact Test (A) – changed the description of the clothing for consistency with 49 CFR, Part 572, Subpart O, §572.134 (c) (1)
-
Section 8.3 Thorax Impact Test (B) – added the mass of 1/3 of the suspension cable length to the probe mass and added specification of the mass moment of inertia of the probe for consistency with 49 CFR, Part 572, Subpart O, §572.137 (a)
-
Section 8.3 Thorax Impact Test (D)(6) – changed the tolerance of the probe centerline alignments relative to the mid-sagittal plane and the centerline of rib number 3 for consistency with 49 CFR, Part 572, Subpart O, §572.134 (c)(4)
-
Section 8.3 Thorax Impact Test (E)(1) – added one significant digit to the performance specifications for maximum sternum-to-spine displacement and English equivalents for consistency with 49 CFR, Part 572, Subpart O, §572.134 (b)(1)
-
Section 8.3 Thorax Impact Test (E)(2) – changed English equivalent of the peak force for consistency with 49 CFR, Part 572, Subpart O, §572.134 (b)(1)
-
Section 8.3 Thorax Impact Test (E)(3) – changed the performance specifications for peak probe force for consistency with 49 CFR, Part 572, Subpart O, §572.134 (b)(1)
-
Section 8.4 Knee Impact Test (B) – changed the edge radius specification of the probe for consistency with 49 CFR, Part 572, Subpart O, §572.137 (b)
-
Section 8.4 Knee Impact Test (D)(1) – narrowed the specification of the soak temperature for consistency with other certification tests
-
Section 8.4 Knee Impact Test (E)(1) – added one significant digit to the performance specifications for peak impact force and English equivalents for consistency with 49 CFR, Part 572, Subpart O, §572.136 (b)
-
Section 8.5 Knee Slider Test (D)(2) – narrowed the specification of the soak temperature for consistency with other certification tests
-
Table 2 – corrected the metric specification for Head Back to Backline measurement
-
Section 9.6 Torso Flexion Test (C)(1) – narrowed the specification of the soak temperature for consistency with the certification tests
-
Section 9.6 Torso Flexion Test (C)(2) – changed the torque specification for the lumbar spine cable jam nut for consistency with the NHTSA PADI, dated June 10, 2002
-
Section 9.6 Torso Flexion Test (C)(6) – changed the specification for the angle of the pelvic surface relative to horizontal for consistency with 49 CFR, Part 572, Subpart O, §572.135, Figure O4
-
Section 9.6 Torso Flexion Test (C) – added steps 8, 9, 14 and 15 for consistency with 49 CFR, Part 572, Subpart O, §572.135 (c)
-
Section 9.6 Torso Flexion Test (C)(13) – added tolerance to flexion angle for consistency with 49 CFR, Part 572, Subpart O, §572.135 (b)(1)
-
Section 9.6 Torso Flexion Test (D) – changed force specifications for consistency with 49 CFR, Part 572, Subpart O, §572.135 (b)(1)
-
Section 9.6 Torso Flexion Test (D) – added return angle specifications for consistency with 49 CFR, Part 572, Subpart O, §572.135 (b)(2)
-
Section 9.7 Low-speed Thorax Impact Test – added as an inspection test
Recommended Content
Ground Vehicle Standard | User's Manual for the Hybrid III Large Male Test Dummy |
Ground Vehicle Standard | User’s Manual for the 50th Percentile Male Hybrid III Dummy |
Ground Vehicle Standard | Low Speed Thorax Impact Test Procedure for the HIII5F Dummy |
Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Table 1 | Torque specifications | |
Unnamed Dataset 3 | ||
Unnamed Dataset 4 | ||
Unnamed Dataset 5 | ||
Unnamed Dataset 6 | ||
Unnamed Dataset 7 | ||
Unnamed Dataset 8 | ||
Unnamed Dataset 9 | ||
Unnamed Dataset 10 | ||
Unnamed Dataset 11 | ||
Unnamed Dataset 12 | ||
Unnamed Dataset 13 | ||
Unnamed Dataset 14 | ||
Unnamed Dataset 15 | ||
Unnamed Dataset 16 | ||
Unnamed Dataset 17 | ||
Table 2 | Hybrid III small adult female external dimensions | |
Table 3 | Hybrid III small adult female total and segment masses |
Issuing Committee
Dummy Testing and Equipment Committee
The Dummy Testing Equipment Committee (DTEC) is a group of experts with experience in the area of certification and handling of Anthropomorphic Test Devices (ATD), more commonly known as crash test dummies, and equipment related to ATD. The DTEC seeks to standardize the use and certification of ATD so that test data are both repeatable and reproducible.
Reference
Number | Title |
---|---|
J1733_201811 | Sign Convention for Vehicle Crash Testing |
J211/1_202208 | Instrumentation for Impact Test Part 1 - Electronic Instrumentation |
J2517_201608 | Hybrid III Family Chest Potentiometer Calibration Procedure |
J2878_201606 | Low Speed Thorax Impact Test Procedure for the HIII5F Dummy |
J2915_202205 | H-III5F Spine Box Update to Eliminate Noise |
J2921_202303 | H-III5F Chest Jacket Harmonization |
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.