This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Control of Residual Stress in Practice
Annotation ability available
Sector:
Language:
English
Abstract
THIS paper discusses the following phases of the residual stress problem, each section containing copious references to work done in the field:
-
1.
General effects of residual stresses.
-
2.
Classification of control measures.
-
3.
Control of residual-stress failures due to mechanical loads plus chemical factors.
-
4.
Control of season cracking and related failures.
-
5.
Control of residual stress to raise fatigue strength.
-
6.
Control in parts loaded statically and in impact.
-
7.
Strengthening of parts by shrinking and overstraining.
-
8.
Dimensional stability and other physical properties.
Recommended Content
Authors
Citation
Sachs, G., "Control of Residual Stress in Practice," SAE Technical Paper 550283, 1955, https://doi.org/10.4271/550283.Also In
References
- Nature Vol. 153 April 22 1944 494 495 “Thermal Fatigue of Metals,” Boas W. Honeycombe. R. W. K.
- VDI Zeitschrift Vol. 71 Oct. 22 1927 1511 1516 “Residual Stresses in Metals,” Sachs. G.
- Metals & V Alloys, Vol. 5 June 1934 131 135 “Internal Stresses - a Correlated Abstract,” Barrett. C. S.
- 177 228 “Residual Stresses in Metals,” Sachs, G. “Handbuch der Metallphysik,” Masing. G. Akademische Verlagsgesellschaft M.B.H. Leipzig 1937
- Iron Age Vol. 148 Sept. 18 1941 63 71 “Measurement of Residual Stresses in Metals,” Sachs G. Espey. G.
- Proceedings of Society for Experimental Stress Analysis Vol. 2 No. 1 1944 147 156 “Critical Review of Various Methods of Residual Stress Measurement,” Barrett. C. S.
- “Symposium on Stress-Corrosion Cracking of Metals.” ASTM and AIME Philadelphia and New York 1945
- “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- ASTM Proceedings Vol. 49 1949 539 583 “Residual Stresses in Metals,” Baldwin, W. M. Jr.
- 459 578 “Residual Stresses,” Horger, O. J. “Handbook of Experimental Stress Analysis,” Hetenyi. M. Wiley New York 1950
- “Residual Stress Measurements,” Treuting R. G. ASM Cleveland 1952
- “Residual Stresses in Metals and Metal Construction,” Osgood. W. R. Reinhold New York 1954
- 209 229 “Factors Influencing Stress Cracking of Brass Cartridge Cases,” Sachs, G. Espey, G. Clark, S. M. “Symposium on Stress-Corrosion Cracking of Metals.” ASTM and AIME Philadelphia and New York 1945
- Wright Air Development Center Report No. 53–254 1953 “Survey of Low-Alloy Aircraft Steels Heat-Treated to High Strength Levels, Part 3: Failure Cases,” Sachs. G.
- AIME Transactions (Institute of Metals Division) Vol. 147 1942 250 264 “Relief of Residual Stress in Some Aluminum Alloys,” Kempf L. W. Van Horn. K. R.
- Proceedings of Society for Experimental Stress Analysis Vol. 3 No. 1 1945 40 61 “Study of Certain Mechanically Induced Residual Stresses,” Richards. D. G.
- Journal of Metals Vol. 5 March 1953 405 422 “Residual Stresses Introduced during Metal Fabrication,” Van Horn. K. R.
- Wright Air Development Center Report No. 53–254 1953 “Survey of Low-Alloy Aircraft Steels Heat-Treated to High Strength Levels, Fart 1: Hydrogen Embrittlement,” Sachs G. Beck W.
- 351 365 “Delayed Cracking in Hardened Alloy Steel Plates,” Bucknall, E. H. Nicholls, W. Toft, L. H. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- AIME Transactions (Institute of Metals Division) Vol. 147 1942 74 88 “Residual Stress in Sunk Cartridge-Brass Tubing,” Sachs G. Espey. G.
- U. S. Bureau of Standards Journal of Research Vol. 28 June 1942 755 772 “Relief of Residual Stress in Streamline Tierods,” Pollard R. E. Reinhart. F. M.
- American Foundryman Vol. 10 September 1946 37 47 “Steel Castings and Weldraents, Residual Stress Relief,” Jelm C. R. Herres. S. A.
- VD1 Zeitschrift Vol. 83 Feb. 4 1939 129 132 “X-Ray Determination of Stresses in Specimens of Unalloyed Steel in Tensile Tests at above Yield Point,” Bollenrath, F. Hauk, V. Osswald. E.
- Journal of Institute of Metals Vol. 67 1941 87 99 “Quenching Stresses in Aluminum Alloys,” von Zeerleder. A.
- Zeitschrift fur Metallkunde Vol. 36 March 1944 70 72 “Crystallite Deformation at Surface of Parts Containing Residual Stresses Subjected to Static Tensile and Compressive Loads,” Schaal. A.
- 171 177 “Relief of Internal Stresses in Aluminum Alloys by Cold Working,” Betteridge, W. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- Metallwirtschaft Vol. 10 Oct. 9 783 788 “Cracking of Cold-Drawn Steel Bars,” Fahrenhorst W. Sachs. G.
- A.I.M.E. Transactions (Institute of Metals Division) Vol. 89 1930 233 255 “Internal Stress and Season Cracking in Brass Tubes,” Crampton. D. K.
- Mitteilungen der Deutschen Matcrialprufungsanstaltcn Vol. 16 1932 38 67 “Investigation of Properties of Cold-Drawn Wire and Force Requirements for Wire Drawing,” Linicus W. Sachs. G.
- Archiv fur das EisenhÜttenwesen Vol. 8 May 1935 515 516 “Residual Stresses in Burnished Steel Rod,” Bühler. H.
- Archiv fÜr das Eisenhiittcnwesen Vol. 8 April 1935 465 466 “Effect of Die Contour on Residual Stresses and Strength Properties on Cold-Drawn Steel Rod,” Bühler. H.
- “Forming of Austenitic Chromium-Nickel Stainless Steels,” Krivobok V. N. Sachs. G. International Nickel Co. New York 2nd ed. 1954
- VDI Zeitschrift Vol. 78 Aug. 4 1934 921 925 “Increase ot Endurance Limit of Notched Structural Parts by Residual Stress,” Thum A. Bautz. W.
- VDI Zeitschrift Vol. 81 Feb. 27 1937 276 278 “Effect of Residual Thermal Stresses on Fatigue Strength,” Thum A. Erker. A.
- Welding Journal Vol. 22 February 1943 63s 78s “Investigation of Behavior of Residual Stresses under External Load and Their Effect on Safety,” Norton J. T. Rosenthal. D.
- Welding Journal Vol. 25 May 1946 269s 276s “X-Ray Diffraction Study of Notch-Bend Test,” Norton, J. T. Rosenthal, D. Maloof. S. B.
- Welding Journal Vol. 25 November 1946 729s 735s “Study of Effect of Residual Compression on Fatigue of Notched Specimens,” Norton, J. T. Rosenthal, D. Maloof. S. B.
- ASM Transactions Vol. 27 September 1939 821 836 “Internal Stresses in Piston Rods of Large Diesel-Engine Ocean Liner,” Sachs. G.
- Iron Age Vol. 155 March 29 1945 40 49 “Mechanical and Metallurgical Advantages of Shotpeening,” Horger. O. J.
- Metals & Alloys Vol. 10 January 1939 19 23 “Improved Aircraft Propellers by Surface Rolling,” Sachs. G.
- Journal of Applied Mechanics Vol. 2 December 1935 A128 A136 “Effect of Surface Rolling on Fatigue Strength of Steel,” Horger. O. J.
- 85 142 “Stressing Axles and Other Railroad Equipment by Cold Rolling,” Horger, O. J. “Surface Stressing of Metals.” ASM Cleveland 1947
- Mitteilungen des Wohler-Institute, No. 41 1948 “Measuring Stresses and Plastic Deformations in Surface-Pressed Test Bars,” Föppl. H.
- Product Engineering Vol. 22 March 1951 101 124 “Fatigue Failures Are Tensile Failures,” Almen. J. O.
- 129 204 “Relief and Redistribution of Residual Stresses in Metals,” Richards, D. G. “Residual Stress Measurements.” ASM Cleveland 1952
- 261 278 “Shotblasting and Its Effects on Fatigue Life,” Zimmerli, F. P. “Surface Treatment of Metals.” ASM Cleveland 1941
- Proceedings of Society for Experimental Stress Analysis Vol. 2 No. 1 1944 178 190 “Improving Fatigue Resistance by Shotpeening,” Horger O. J. Neifert. H. R.
- Proceedings of Society for Experimental Stress Analysis Vol. 2 No. 2 1945 1 10 “Shotpeening to Improve Fatigue Resistance,” Horger O. J. Neifert. H. R.
- 395 415 “Prevention of Fatigue Failures in Metal Parts by Shotpeening,” Brookman J. G. Kiddle, L. “Failure of Metals by Fatigue.” Melbourne University Press Melbourne 1947
- SAE Journal Vol. 56 November 1948 36 39 “Shotpeening,” Zimmerli F. P. Straub. J.
- VDI Zeitschrift Vol. 82 July 23 1938 885 889 “Endurance of Hollow Crankshaft Pins with Internal Reinforcement,” Cornelius H. Bollenrath. F.
- Metallurg (Russian) Vol. 8 1940 30 37 “Residual Internal Stresses in Steels Hardened by High-Frequency, Surface-Hardening Process,” Kontorovich I. E. Livshits. L. C.
- ASTM Technical Publication No. 72 1947 “Symposium on Testing of Parts and Assemblies,” 47 75 Horger O. J. Lipson. C. H.
- Archiv für das Eisenhüttenwesen Vol. 12 March 1939 445 448 “Influence of Case Hardening on Alternating Bending and Torsion Fatigue Strength of Smooth and Transversely Bored Test Specimens,” Wiegand H. Scheinost. R.
- VDI Zeitschrift Vol. 84 July 20 1940 505 510 “Surface and Fatigue Strength,” Wiegand. H.
- Transactions of American Society for Steel Treating Vol. 18 1930 423 439 “Stresses and Cracks in Hardened and Ground Steel,” Brophy. G. R.
- Ingeniorvidenskabelige, Skrifter A, No. 43 1937 “Machining and Residual Stresses,” Henriksen. E. K.
- ASME Transactions Vol. 73 January 1951 69 76 “Residual. Stresses in Machined Surfaces,” Henriksen. E. K.
- VDI Zeitschrift Vol. 88 Dec. 23 1944 681 686 “Bending Fatigue Strength of Case-Hardened and Nitrided Steels Containing Grinding Cracks,” Staudinger. H.
- Journal of Technical Physics (Leningrad) Vol. 16 No. 7 1946 791 802 “Residual Stresses Caused by Grinding,” Glickman L. A. Stepanoy. V. A. Engineers' Digest
- ASM Transactions Vol. 36 1946 389 451 “Detection, Causes, and Prevention of Injury in Ground Surfaces,” Tarasoy. L. P.
- ASME Transactions Vol. 73 April 1951 337 342 “Residual Grinding Stresses in Mild Steel,” Frisch J. Thomsen. E. G.
- NACA TN 2324 1951 “Fatigue Strength of Aircraft Materials; Axial-Load Fatigue Tests on Unnotched Sheet Specimens of 24S–T3 and 75S–T6 Aluminum Alloys and of SAE 4130 Steel,” Grover, H. J. Bishop, S. M. Jackson. I.. R.
- U. S. Bureau of Standards Journal of Research Vol. 40 January 1948 31 59 “Physical Properties of Electrodeposited Chromium,” Brenner, A. Burkhead, P. Jennings. C.
- 107 118 “Stress in Electrodeposited Metals,” Hothersall, A. W. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- U. S. Bureau of Standards Journal of Research Vol. 42 February 1949 105 123 “Calculation of Stress in Electrodeposits from Curvature of Plated Strip,” Brenner A. Senderoff. S.
- V. S. Bureau of Standards Journal of Research Vol. 42 February 1949 89 104 “Spiral Contractometer for Measuring Stress in Electrodeposits,” Brenner A. Senderoff. S.
- U. S. Bureau of Standards Journal of Research Vol. 43 August 1949 101 112 “Effect of Chromium Plating on Endurance Limit of Steels Used in Aircraft,” Logan. H. L.
- Product Engineering Vol. 22 June 1951 109 116 “Fatigue Loss and Gain by Electroplating,” Almen. J. O.
- Welding Journal Vol. 28 March 1949 89s 97s “Tests of Large Welded-Steel Box Girders,” Stang A. H. Jaffe. B. S.
- Welding Journal Vol. 29 September 1950 484s 493s “Distribution of Locked-in Stresses in Large Welded-Steel Box Girder,” Vasta. J.
- 163 168 “Internal Stresses in Glassware,” Hynd, W. C. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- Welding Journal Vol. 28 May 1949 193s 203s “Evaluation of Effect of Residual Stresses,” Greene. T. W.
- Welding Journal Vol. 30 March 1951 135s 145s “Stress Relieving and Fracture Strength,” Swan, D. Lytle, A. R. McKinsey. C. R.
- Welding Journal Vol. 25 March 1946 171s 185s “Controlled Low-Temperature Stress Relieving,” Greene T. W. Holzbaur. A. A.
- Welding Journal Vol. 28 August 1949 354s 364s “Report of Some Recent Research into Measurement and Relaxation of Residual Stresses,” Soete. W.
- University of Illinois Engineering Experiment Station Bulletin, Series 361 1946 “Residual Stresses in Welded Structures,” Wilson W. M. Hao. C. C
- Welding Journal Vol. 26 April 1947 193s 214s “Investigation of Influence of Hydrogen on Ductility of Arc Welds in Mild Steel,” Flanigan. A. E.
- Proceedings of Society for Experimental Stress Analysis Vol. 7 No. 2 1949 45 72 “Strength of Inserted Dies,” Sachs, G. Lubahn, J. D. Ebert. L. J.
- “Overstrain of Metals and Its Application to Autofrettage Process,” Macrae. A. E. H. M. Stationary Office London 1930
- 209 218 “Autofrettage,” Warren, A. G. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- Iron & Steel Institute Journal Vol. 133 1936 427p 442p “Fatigue Resistance of Spring Steels,” Becker M. L. Phillips. C. E.
- Machine Design Vol. 17 January 1945 107 112 “Utilizing Effects of Cold Setting in Springs,” Wahl. A. M.
- Proceedings of Society for Experimental Stress Analysis Vol. 4 No. 1 1946 64 73 “Measurement of Residual Stresses in Torsion Bar Springs,” Fuchs H. O. Mattson. R. L.
- Machinery (NY) Vol. 52 June 1946 152 157 “Utilizing Residual Forming Stresses in Flat Steel Springs,” Troy. W. C.
- 195 207 “Production of Favorable Internal Stresses in Helical Compression Springs by Prestressing,” Sopwith, D. G. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- Zeitschrift für Angcwandte Mathematik und Mechanik Vol. 5 August 1925 281 293 “Parts of Rotational Symmetry Rotating in Range of Permanent Deformation,” Laszlo. F.
- Engineering Vol. 168 Oct. 28 1949 437 440 “Local Overstraining of Metals,” Laszlo. F.
- Broom Boveri Review Vol. 16 September 1929 243 253 “Internal Stresses and Heat Stresses and Their Relation to Steam Turbine Construction,” Honnegger. E.
- SAE Transactions Vol. 54 September 1946 446 475 “Improving Engine Parts by Direct Measurement of Strain,” Anderson. R. G.
- Steel Vol. 118 June 3 1946 104 106 “Prestressing Rotating Discs,” Dobkin. H.
- 139 152 “Some Internal Stresses in Turbine Rotors,” Caplan, M. C. Jolley, L. B. W. Reeman, J. “Symposium on Internal Stresses in Metals and Alloys.” Institute of Metals London 1948
- Journal of Aeronautical Sciences Vol 15 March 1948 151 154 “Dependence of Stress-Strain Curves on Cold-Worked Metals upon Testing Direction,” Klinger L. J. Sachs. G.
- SAE Quarterly Transactions Vol. 3 July 1949 480 489 “Design of Aircraft Structures for ‘Mass Production,’ ” Wheelon. O. A. SAE Journal
- Zeitschrift fülr Metallkunde Vol. 17 July 1925 227 228 “On Removal of Residual Stress by Annealing,” Polanyi M. Sachs. G.
- 97 128 “Residual Stress States Produced in Metals by Various Processes,” Wishart, H. B. “Residual Stress Measurements.” ASM Cleveland 1952
- Archiv für das Eisenhüttenwesen Vol. 8 November 1934 219 222 “Superposition of Heat and Transformation Stresses in Quenched Steel Tube,” Bühler H. Scheil. E.