AS5969D FITTING ASSEMBLY, UNION, AXIALLY SWAGED, HYDRAULIC 5080 PSI

MATERIALS:

CODE LETTER “T”

FINISH:

1. TITANIUM - NONE

COATINGS/LUBRICANTS /16/:

1. a
   NO SUFFIX CODE LETTER

   1. (1)
      RINGS - THE OUTER SURFACE SHALL HAVE A .125 INCH MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. PTFE COATING OR PAINT SHALL BE RESISTANT TO AS1241 FLUID WHEN USED. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958.
   2. (2)
      BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID.
2. b
   SUFFIX CODE LETTER A

   1. (1)
      RINGS - NO BLUE PTFE COATING OR PAINT. THE WORD “BLUE” SHALL BE MARKED ON THE RING TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958.
   2. (2)
      BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID.
3. c
   SUFFIX CODE LETTER B

   1. (1)
      RINGS - PARTIALLY (.125 INCH MINIMUM WIDTH) OR COMPLETELY ANODIZED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958.
   2. (2)
      BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT, MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID.

PROCUREMENT SPECIFICATION: AS5958 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LISTING FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE www.eAuditNet.com FOR CURRENT QPL ON-LINE.

DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION.

IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN.

FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. THE AFTER SWAGE ACCEPTABILITY LIMIT DIMENSION "Z" FOR EACH PORT SIZE IS DEFINED IN AS5959.

SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra.

DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.

1. a
   DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED
2. b
   DIMENSIONAL TOLERANCES SHALL BE ±.005 INCHES UNLESS OTHERWISE SPECIFIED
3. c
   ANGULAR TOLERANCES SHALL BE ±.50 DEGREES UNLESS OTHERWISE SPECIFIED
4. d
   BREAK ALL EDGES .003 TO .010 INCHES UNLESS OTHERWISE SPECIFIED

INTERPRETATION OF DRAWING PER ARP4296.

THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN.

FOR JUMP SIZE FITTINGS, A TRANSITION DIAMETER WILL OCCUR IN THIS AREA.

DIMENSION A IS THE FITTING ASSEMBLY LENGTH PRIOR TO SWAGE AND A1 IS THE FITTING BODY LENGTH BEFORE SWAGE.

A CHANGE BAR ( | ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.

EXAMPLE OF PART NUMBER:

UNPAINTED RINGS "CODE A" WERE NEEDED TO PREVENT COATING/PAINT DEBRIS OF RINGS "NO CODE" IN CONTAMINATION SENSITIVE SYSTEMS. NO CODE LETTER AND CODE LETTER “A” PARTS ARE NOT RECOMMENDED FOR PROCUREMENT AFTER 03/31/2014 AND SHOULD BE REPLACED BY ANODIZED PARTS WITH CODE LETTER “B”.