Search
Advanced Search
of the following are true
(
)

Results

Items (211,878)
This SAE Recommended Practice covers passive torque biasing axle and center differentials used in passenger car and light truck applications. Differentials are of the bevel gear, helical gear, and planetary types, although other configurations are possible.
Drivetrain Standards Committee
This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET. This document is intended to provide design direction for the single phase nominal 120 VAC as it interfaces within the truck 12 VDC battery and electrical architecture providing power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off.
Truck and Bus Electrical Systems Committee
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
A-6C2 Seals Committee
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
AE-8C1 Connectors Committee
This specification covers three classes of fuel-resistant polysulfide (T) sealing compound with high strength and temperature characteristics, supplied as a two-component system which cures at room temperatures.
AMS G9 Aerospace Sealing Committee
This specification covers a corrosion and moderate heat-resistant steel in the form of investment castings.
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Aerospace Recommended Practice (ARP) provides an overview of the various types of polytetrafluoroethylene (PTFE) backup rings for hydraulic and pneumatic fluid power applications, including their advantages and disadvantages.
A-6C2 Seals Committee
This specification covers a corrosion-resistant steel in the form of welding wire.
AMS E Carbon and Low Alloy Steels Committee
The purpose of this SAE Aerospace Information Report (AIR) is to disseminate qualitative information regarding foreign object debris (FOD) damage to the gas path of rotorcraft gas turbine engines and to discuss methods of FOD prevention. Although turbine-powered fixed-wing aircraft are also subject to FOD, the unique ability of the rotorcraft to hover above, takeoff from, and land on unprepared surfaces creates a special need for a separate treatment of this subject.
S-12 Powered Lift Propulsion Committee
This specification covers electrical connections made with single, solid, round copper or copper alloy wire wrapped around copper alloy terminals without the use of solder.
AMS B Finishes Processes and Fluids Committee
This specification covers a glass-roving-filled silicone resin in the form of compression moldings or transfer moldings.
AMS P Polymeric Materials Committee
This Aerospace Recommended Practice (ARP) describes a standard method and means for measuring or calibrating the "Spectrum Amplitude" output of an impulse generator.
AE-4 Electromagnetic Compatibility (EMC) Committee
This specification cover glass cloth impregnated with a heat-reactive, thermosetting, addition-cure polyimide resin system, the resin to be supplied in a "B" stage condition.
AMS P17 Polymer Matrix Composites Committee
This SAE Aerospace Recommended Practice (ARP) provides guidance to plan and perform validation and verification of IVHM systems. The intent of this ARP is to help the reader appreciate and understand additional objectives and activities of validation and verification processes, beyond validation and verification of the vehicle, that arise due to the nature of an IVHM System. This includes an end-to-end evaluation of the entire IVHM system, noting that IVHM is a “system of systems.” In order to perform validation and verification, the user must determine what they are using IVHM for, including the criticality of the application. The process should then determine appropriateness of the data corresponding to the application criticality. This document provides validation and verification guidance for IVHM as: (1) a system of systems, (2) a system, and (3) elements within a system. While this document is not intended to be prescriptive, it is a reference guide that highlights and discusses
HM-1 Integrated Vehicle Health Management Committee
The product shall consist of 5-ply yarn having 720 continuous filaments per ply and a maximum of 4 turns per inch (25.4 mm).
AMS P17 Polymer Matrix Composites Committee
This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
G-22 Aerospace Engine Supplier Quality (AESQ) Committee
This set of criteria is intended for use by accredited Certification Bodies (CBs) to establish compliance and grant certification to AS6081A. It may also be used by others to assess compliance to AS6081A requirements.
G-19 Counterfeit Electronic Parts Committee
This specification covers "S" glass in one style of woven fabric with an HTS-904 finish.
AMS P17 Polymer Matrix Composites Committee
This specification covers epoxy-resin-impregnated carbon-fiber broadgoods and tape in the form of multi-plied unidirectional layers constructed from the same or uniform fibers and supplied as broadgood rolls, tape, or cut sheet. The individual ply orientation shall be as ordered.
AMS P17 Polymer Matrix Composites Committee
This specification covers a style 7781 glass cloth impregnated with a heat-curable polyester resin system, the resin being processed to a “B” stage condition, and furnished in the form of continuous rolls.
AMS P17 Polymer Matrix Composites Committee
Items per page:
1 – 50 of 211878