Results
This specification covers an aluminum alloy in the form of sheet and plate from 0.006 to 6.000 inches (0.15 to 152.40 mm), inclusive, in nominal thickness (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings in the solution heat-treated condition, 5 inches (127 mm) and under in nominal diameter or least distance between parallel sides (thickness) having a maximum cross-sectional area of 50 square inches (323 cm2), and stock of any size for forging, flash welded rings, or heading.
This specification covers aluminum alloy sheet laminated with one or more layers of unidirectional aramid fiber/epoxy prepreg. The outer layers are always aluminum alloy.
This specification and its detail slash specifications cover the requirements for media to be used in controlled shot peening of metal parts.
This specification covers one type of titanium alloy plate in the beta-annealed condition up through 4.000 inches (101.60 mm) inclusive, in thickness (see 8.6).
This specification covers requirements for the material, design, testing and packaging of straight thread tube fitting boss O-rings. O-rings covered by this specification are acrylonitrile-butadiene rubber.
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specification requirements of wrought carbon and low-alloy steel products and of forging stock.
This specification covers a fluorocarbon elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. For molded rings, molded compression seals, and molded-in-place gaskets for aeronautical and aerospace applications, use the AMS7379 specification.
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.
This specification covers a corrosion-resistant steel in the form of wire.
This specification covers a corrosion-resistant steel in the form of welding wire.
This specification covers an aluminum alloy in the form of plate 1.500 to 6.000 inches (38.1 to 152.40 mm) thick (see 8.5).
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat treated (H1025) condition.
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of nickel, nickel alloys, and cobalt alloys ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing produced with cross sectional area of 32 in2 (206 cm2) maximum.
This specification covers a tantalum alloy in the form of sheet, strip, and plate from 0.010 through 0.250 inch (0.25 through 6.35 mm), inclusive.
This specification covers two types of free-machining, corrosion and heat-resistant steel in the form of bars, wire, forgings, and forging stock.
This specification covers optical-quality coatings applied to instrument glasses.
This specification covers a low-alloy steel in the form of welding wire.
This specification establishes the requirements for chromate conversion coatings on magnesium alloys.
This specification covers a corrosion and heat-resistant steel in the form of investment castings.
This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inch (6.35 to 102.0 mm) inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion-resistant steel in the form of investment castings.
Items per page:
50
1 – 50 of 211955