Search
Advanced Search
of the following are true

Results

Items (206,858)
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR
Truck and Bus Foundation Brake Committee
This AIR was prepared to inform the aerospace industry about the electromagnetic interference measurement capability of spectrum analyzers. The spectrum analyzers considered are of the wide dispersion type which are electronically tuned over an octave or wider frequency range. The reason for limiting the AIR to this type of spectrum analyzer is that several manufacturers produce them as general-purpose instruments, and their use for EMI measurement will give significant time and cost savings. The objective of the AIR is to give a description of the spectrum analyzers, consider the analyzer parameters, and describe how the analyzers are usable for collection of EMI data. The operator of a spectrum analyzer should be thoroughly familiar with the analyzer and the technical concepts reviewed in this AIR before performing EMI measurements
AE-4 Electromagnetic Compatibility (EMC) Committee
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a Ability of the parking brake system to lock the braked wheels. b The trailer holding or sliding on the grade, fully loaded, or unloaded. c Applied manual effort. d Unburnished or burnished brake lining friction conditions. e Down and upgrade directions
Truck and Bus Brake Systems Committee
This Aerospace Information Report (AIR) is intended to provide information relating to the construction, calibration, and usage of parallel plate transmission lines in electromagnetic compatibility susceptibility testing
AE-4 Electromagnetic Compatibility (EMC) Committee
This specification covers an aluminum alloy in the form of rolled or cold finished bars and rods of the sizes specified in 3.3.1.1 (see 8.5
AMS D Nonferrous Alloys Committee
This specification covers one type of copper alloy (brass) in the form of bars and rods up to 4.000 inches (101.60 mm) in nominal diameter, thickness between parallel sides, or width as defined in Tables 3 through 6 (see 8.6
AMS D Nonferrous Alloys Committee
This specification covers a polysulfide sealing compound with low adhesive strength, supplied as a two-component system that cures at room temperature
AMS G9 Aerospace Sealing Committee
This recommended practice establishes the requirements and procedures for Barkhausen Noise (BN) inspection of ferromagnetic steel components. See Appendix B for a list of common materials for BN inspection. Applications of the method are listed in 1.2 through 1.5
AMS K Non Destructive Methods and Processes Committee
This SAE Recommended Practice provides test methods and criteria for evaluating the internal cleanliness and air leakage for engine charge air coolers. This SAE Recommended Practice also provides nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air cooling system operational performance parameters
Cooling Systems Standards Committee
This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway service on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose vehicles. For procedures and minimum performance requirements for wheels used on trucks, see SAE J267, and for wheels used on passenger cars, see SAE J328. For the application of passenger car and light truck wheels (inset less than 0.10 m) to this trailer service, use this procedure. For the application of heavier truck wheels (inset 0.10 m (or more)) use SAE J267. Mobile home service is outside the scope of this document. There are two basic test procedures described, a cornering fatigue test and radial fatigue test. The cornering test is directed at the wheel disc; whereas the radial test also examines the rim and attachment portion of the wheel. Both test procedures are required to obtain a
Wheel Standards Committee
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, 12 inches (305 mm) and under in nominal diameter or maximum cross-sectional dimension and forging stock
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers the requirements for brush plating of cobalt by electrodeposition
AMS B Finishes Processes and Fluids Committee
This specification covers a titanium alloy in the form of sheet 0.025 through 0.100 inch (0.63 through 2.54 mm), inclusive, in thickness (see 8.7
AMS G Titanium and Refractory Metals Committee
This specification covers a nickel-copper alloy in the form of castings
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a nickel-copper alloy in the form of castings
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Standard provides requirements to support applications for the maneuver sharing and coordinating service (MSCS) beyond broadcast of basic safety messages (BSMs). This is to improve road safety and traffic efficiency by sharing and coordinating vehicle maneuvers via vehicle-to-everything (V2X) communications. This document lays out use case scenarios and defines vehicle-to-vehicle (V2V) application protocols, system requirements and message sets for MSCS. The defined message sets for MSCS will result in identifying new message types, data frames, and data elements for SAE J2735
V2X Vehicular Applications Technical Committee
This specification covers the requirements for application to fasteners of a corrosion and heat resistant aluminum coating material having a thermosetting inorganic binder and the properties of the finished coating
AMS B Finishes Processes and Fluids Committee
This specification covers a low-alloy steel in the form of welding wire
AMS E Carbon and Low Alloy Steels Committee
This specification covers connector and cable accessory heat shrinkable, electrical insulating, molded components fabricated from various polymer based compositions. These components are intended for use as connector and cable accessory components to provide strain relief, electrical insulation, and environmental sealing
AE-8C1 Connectors Committee
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the function, design, construction, and testing of an on-aircraft Brake Temperature Monitoring System (BTMS), sometimes referred to as a Brake Temperature Indication System (BTIS). NOTE: This ARP does not address: Cockpit ergonomics and Aircraft operating procedures. Various handheld methods of temperature sensing or readouts, as these are not associated with transport aircraft during normal operation. Temperature sensitive paints as a means to indicate exceedance of a landing gear axle temperature threshold due to brake temperature
A-5A Wheels, Brakes and Skid Controls Committee
The SAE Aerospace Information Report (AIR) focuses on the impact of alkali metal-based runway deicers (potassium acetate, potassium formate, and sodium acetate, and sodium formate) have on in-service aircraft EWIS components
AE-8A Elec Wiring and Fiber Optic Interconnect Sys Install
This document provides details of test methods that should be taken into consideration when qualifying fiber optic termini to the product specifications (slash sheets). The product specifications (slash sheets) provide pass/fail criteria, optical and physical intermatability, and interoperability requirements for fiber optic termini in circular, rectangular, and modular type aerospace connectors
AS-3 Fiber Optics and Applied Photonics Committee
This specification establishes the requirements for brush plating of copper by electrodeposition
AMS B Finishes Processes and Fluids Committee
This specification covers flash welded rings fabricated from carbon and low-alloy steels
AMS E Carbon and Low Alloy Steels Committee
This SAE Aerospace Recommended Practice (ARP) establishes general criteria for the installation (e.g., type, location, accessibility, stowage) and crew member training needed for hand-held fire extinguishers
S-9A Safety Equipment and Survival Systems Committee
This SAE Aerospace Standard (AS) defines the performance requirements for equipment to be used by untrained cabin occupants for protection from toxic and irritant atmospheres while on board and during evacuation of an aircraft
A-10 Aircraft Oxygen Equipment Committee
This document describes particulate filter weigh-room recommended practices to provide guidance in the procedures and processes associated with gravimetric filter weighing of engine or vehicle particulate matter (PM) emissions. This recommended practice provides proper procedures to build and maintain a particulate filter weigh room or enclosure to meet the requirements of EPA's 40 CFR Part 1065 and ISO 14065 for obtaining low measurement uncertainty. The content of this recommended practice addresses the following areas: a Particulate Filter Weigh Room b Microbalance Requirements c Filter Conditioning and Handling Requirements d Weighing Process e Equipment Calibration and Maintenance
Emissions Standards Committee
This SAE Standard describes a reference system architecture based on LTE-V2X technology defined in ETSI Release 14. It also describes cross-cutting features unique to LTE-V2X PC5 sidelink (mode 4) that can be used by current and future application standards. The audience for this document includes the developers of applications and application specifications, as well as those interested in LTE-V2X system architecture, testing, and certification
null, null
This SAE Standard describes the methods for testing flexible harness coverings for use on ground vehicle electrical distribution systems, specifically protection from severe mechanical impact. This SAE Standard shall apply to all tapes, extruded tubes, and textile sleeves used for this purpose
Harness Covering Standards Committee
This SAE Information Report is intended to provide a guide to mechanical and machinability characteristics of some SAE steel grades. The ratings and properties shown are provided as general information and not as requirements for specifications unless each instance is approved by the source of supply. The data are based on resources which may no longer be totally accurate. However, this report is retained as a service in lieu of current data
Metals Technical Committee
Items per page:
1 – 50 of 206858