Search
Advanced Search
of the following are true
(
)

Results

Items (212,784)
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
AE-8C1 Connectors Committee
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
A-6C2 Seals Committee
This document contains information and guidance necessary for the development of a representative, repeatable validation program that may be utilized to assess the capability of SHM systems. The nature of SHM data differs from that seen in traditional nondestructive evaluation (NDE) applications in that the position of SHM sensors is fixed and SHM data can be available much more frequently (if not continuously) over time. This document presents methodologies that can be used to arrive at SHM capability while considering the unique nature of SHM deployment. Each SHM system must be considered independently to determine the applicability and limitations of the guidance contained here for each SHM system being assessed.
Aerospace Industry Steering Committee on Structural Health
This SAE Recommended Practice establishes recommended procedures for the issuance, assignment, and structure of Identification Numbers on a uniform basis by states or provinces for use in an Assigned Identification Number (AIN).
VIN - WMI Technical Committee
This specification establishes requirements for thermoset protective coatings in powder form.
AMS G8 Aerospace Organic Coatings Committee
This specification covers an aluminum alloy in the form of sheet and plate from 0.020 to 1.000 inch (0.51 to 25.4 mm) thick (see 8.6).
AMS D Nonferrous Alloys Committee
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This Standard covers Bank and Pitch Instruments which measure and display the angular displacement of bank and pitch from a gyroscopic vertical reference. This reference may be pneumatically or electrically driven and be contained within the instrument display case or located remotely. Unless otherwise specified, whenever the term "Instrument" is used, it is to be understood to be the complete system of gyro component, any auxiliary equipment and display.
A-4 Aircraft Instruments Committee
This SAE Aerospace Standard (AS) establishes the standard installation procedures and torque values for the AS short flareless hydraulic tube fittings in sizes -20 and -24, and parts listed in this standard, made from 6A1-4V Titanium, 15-5 PH CRES, and 7075 Aluminum Alloy.
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This document sets forth several acceptable methods of laser beam divergence measurement techniques.
G-10T Laser Safety Hazards Committee
To provide the curved hose industry and their customers with a recommended practice for applying GD&T procedures to curved hoses and to provide generic curved hose drawings that represent the application of GD&T to typical curved hose parts. Dimensioning and Tolerancing will be in accordance with ASME Y14.5M.
Non-Hydraulic Hose Committee
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
E-25 General Standards for Aerospace and Propulsion Systems
The purpose of this SAE Recommended Practice is to provide dimensions for both standard and thin-wall hoses and to provide commercial and precision tolerances for SAE 20R3 and SAE 20R4 coolant system hoses.
Non-Hydraulic Hose Committee
This SAE Recommended Practice provides minimum performance requirements and uniform procedures for fatigue and impact testing, electrical resistance, and maximum operating temperature (MOT) of wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles.
Wheel Standards Committee
This SAE Standard establishes a uniform test procedure for determining the exterior operational sound level for snowmobiles.
Snowmobile Technical Committee
Items per page:
1 – 50 of 212784