Search
Advanced Search
of the following are true

Results

Items (207,244)
This document covers the general physical, electrical, functional, safety, and performance requirements for conductive power transfer to an electric vehicle using a coupler, which can be hand-mated and is capable of transferring either DC or AC single-phase power using two current-carrying contacts
Hybrid - EV Committee
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included
Truck Crashworthiness Committee
This SAE Recommended Practice applies to commercial vehicles above 4540 kg of gross vehicle weight rating equipped with air brakes used under normal operating conditions. The procedure incorporates high and low-temperature test matrices, but does not fully account for the effects of the environment on brake squeal. Much research is currently underway in this area. This document defines brake squeal as a peak noise level of at least 80 dB(A) between 500 Hz and 17 kHz for air disc and drum brakes on on-road vehicles
Truck and Bus Foundation Brake Committee
This SAE Recommended Practice presents service brake performance requirements for brake systems of all combinations of new passenger cars and new trailers (braked or unbraked) intended for roadway use (excluding special-purpose vehicles such as ambulances, hearses, etc.). Acceptable performance requirements are based on data obtained from SAE J134
Road Test Procedures Standards Committee
Not available
Fasteners Committee
This recommended practice has been developed for use in any EEE system used in the AADHP industries. RPA is especially important to AADHP systems, which are often safety critical applications that must operate for long times in rugged environments. These EEE systems often use EEE components that were originally designed and produced for more benign consumer applications. Although the focus of this recommended practice is on AADHP applications, the process described herein is not limited to AADHP and may be used for EEE systems and components in any industry
Automotive Electronic Systems Reliability Standards
This Recommended Practice applies to commercial vehicles equipped with air disc brakes and above 4536 kg of Gross Vehicle Weight Rating. Other assessments on the friction material or rotor related to wear, durability, correlation to product life, noise, judder, compliance to specific regulations, etc., are not part of this RP (Recommended Practice
Truck and Bus Foundation Brake Committee
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process. This Recommended Practice is applicable during product and process development, product verification and quality control. This Recommended Practice does not replicate or predict actual vehicle performance or part durability
Brake Linings Standards Committee
This document establishes the requirements for technical content and format of hydraulic system diagrams. This document does not establish configuration requirements, material, or performance requirements for any system or component identified herein
Ship Fluid Systems Committee
This SAE Information Report provides SAE’s recommendations for meeting the requirements for REAL NOx accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in OBD regulations 13 CCR 1971.1 and 13 CCR 1968.2
null, null
This SAE Standard is equivalent to ISO Standard 6627 TR. Differences, where they exist, are shown in Appendix A with associated rationale. This SAE Standard specifies the dimensional features of commonly used oil control rings having two steel segments (rails) separated and expanded by one steel expander/spacer. The segments vary in width from 0.4 to 0.6 mm. The assembly width ranges from 2.5 to 4.75 mm. The 4.75 mm width is equivalent to existing 3/16 in applications. Expander design will vary considerably with piston ring manufacturer. The total circumferential deflection and the piston groove depth should be considered when designing these oil rings to optimize the fit of the ring assembly into the piston groove. This document applies to oil control rings up through 125 mm for reciprocating internal combustion engines. It may also be used for piston rings of compressors working under similar conditions
Piston and Ring Standards Committee
The scope of this SAE Recommended Practice is to establish recommended uniform test procedures and minimum static load requirements for vehicle passenger door hinge systems. Tests are described that can be conducted on test fixtures and equipment in laboratory test facilities. The test procedures and minimum performance requirements outlined in this document are based on currently available engineering data. It is intended that all portions of the document be periodically reviewed and revised as additional knowledge regarding vehicle hinge system performance under impact conditions is developed
Motor Vehicle Council
This document lists common terminology for vacuum excavation and sewer cleaning equipment, including component names and specific work completed by these machines. This document also illustrates some common types of equipment
MTC9, Trenching and Horizontal Earthboring Machines
The purpose of this SAE Information Report is to set up a guide as to body, frame, and wheel housing clearance to accommodate tire chains, and also the minimum bogie spacing to permit using chains on both axles. These dimensions apply to trucks, buses, and combinations of vehicles 10 001 lb (4535.06 kg) GVW and over, and are based upon recommendations of the Tire and Rim Association and of the National Association of Chain Manufacturers. The diagram shows clearance for chains over the tire ONLY and allowance must be made for spring deflections in determining fender clearance. See Figure 1 and Table 1
Truck and Bus Total Vehicle Steering Committee
Because of the intense focus on CAFE and fuel emission standards, optimization of the automobile drivetrain is imperative. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies the dynamometer test procedure which maps a manual transmission’s efficiency. The document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine “in-gear” transmission efficiency. The second procedure measures parasitic losses experienced while in neutral at nominal idling speeds and also churning losses while in gear. The application of this document is intended for passenger car and light truck. All references to transmissions throughout this document include transaxles
SAE IC Powertrain Steering Committee
This SAE Recommended Practice covers electric speedometer systems for general on-road (passenger car, multi-purpose passenger vehicle, truck, and bus) applications
Odometer and Speedometer Standards
This specification covers characteristics for chemistry, microstructure, density, hardness, size, shape, and appearance of zirconium oxide-based ceramic shot, suitable for peening surfaces of parts by impingement
Surface Enhancement Committee
This SAE Standard provides test procedures, requirements, and guidelines for reflex reflectors
Signaling and Marking Devices Stds Comm
Headlamps should illuminate the traffic scene ahead of the vehicle in such a way that the driver can operate the vehicle safely and in a relaxed manner. At the same time, negative effects on drivers of other vehicles, pedestrians and other people should be minimized. Various technical parameters such as beam pattern, mounting height, headlamp aiming, and source spectrum can be tuned to find the necessary compromise. The physiology of the vision system under specific nighttime conditions strongly influences these factors and how headlamps can be best optimized for visibility and comfort. The SAE Improved Roadway Illumination task force collected and reviewed relevant research on these topics. This document is a comprehensive summary of this information. The goal is to enable lighting experts, advocacy groups, and non-experts (journalists, consumer organizations, car drivers) to better understand the benefits and tradeoffs of improved roadway lighting with modern headlamp technology. It
Road Illumination Devices Standards Committee
This SAE Recommended Practice provides guidance for the construction, operation, and maintenance of LNG powered medium, heavy-duty vehicles and all LNG vehicles used for public transit or commercial applications
Truck and Bus Powertrain Committee
This document provides a list of data elements and event triggers for recording of event data relevant to crash investigations for heavy vehicles. The list of data elements includes recommended source(s) and formatting
Truck and Bus Event Data Recorder Committee
It is expected that Level 4 and 5 automated driving systems-dedicated vehicles (ADS-DVs) will eventually enable persons to travel at will who are otherwise unable to obtain a driver's license for a conventional vehicle, namely, persons with certain visual, cognitive, and/or physical impairments. This information report focuses on these disabilities, but also provides guidance for those with other disabilities. This report is limited to fleet operated on-demand shared mobility scenarios, as this is widely considered to be the first way people will be able to interact with ADS-DVs. To be more specific, this report does not address fixed route transit services or private vehicle ownership. Similarly, this report is focused on road-worthy vehicles; not scooters, golf carts, etc. Lastly, this report does not address the design of chair lifts, ramps, or securements for persons who use wheeled mobility devices (WHMD) (e.g., wheelchair, electric cart, etc.), as these matters are addressed by
On-Road Automated Driving (ORAD) Committee
This SAE Standard provides test procedures for air and air-over-hydraulic disc or drum brakes used for on-highway commercial vehicles over 4536 kg (10000 pounds) GVWR. This recommended practice includes the pass/fail criteria of Federal Motor Vehicle Safety Standard No. TP-121D-01
Truck and Bus Foundation Brake Committee
This SAE Standard establishes a uniform test procedure and performance requirements for permanently installed petrol fuel systems in personal watercraft. This SAE Standard does not apply to outboard powered personal watercraft and jet powered surfboards
Personal Watercraft Committee
The materials defined by this U.S. CAR / S.A.E Recommended Practice are low VOC water based coatings for automotive tooling and general maintenance
USCAR
The scope of SAE J3143 will cover non-metallic line assemblies intended for containing and circulating lubricant (PAG, POE compressor oils), liquid, and gaseous R-134a, R-152a, or R-1234yf refrigerant in automotive air-conditioning systems. SAE J3143 will also provide the necessary hose permeation values used in SAE J2727 mobile air-conditioning system refrigerant emission charts. The assembly shall be designed to minimize permeation of the refrigerant, contamination of the system, and to be functional over a temperature range of -30 to 125 °C. Specific construction details are to be agreed upon between user and supplier. Figure 1 shows a typical A/C system with TXV
Interior Climate Control MAC Supplier Committee
This SAE Recommended Practice defines the principal terms and equations pertaining to automotive automatic transmission clutch plate, band, or other wet-friction systems. The terms apply directly to friction-system testing as is typically conducted on inertia-stop test equipment. Some terms can be directly applied to the analysis of friction in the transmission or brake assembly and other friction-test equipment. The glossary presents terms used to describe the set-up, testing, and results of tests as shown in Figure 1, which were taken on a clutch SAE No. 2 machine. The glossary is intended to provide a collection of definitions in the hope of eliminating confusion in development and their application to passenger cars and trucks. This document focuses on the terminology of friction-system testing. References for this type of testing are shown in Section 2
Automatic Transmission and Transaxle Committee
This SAE Recommended Practice provides minimum performance and test criteria for the emergency steering of specified machines in the event of an engine or steering power source failure. This criteria shall enable machine manufacturers to uniformly evaluate emergency steering capability. This recommended practice is specifically limited to tractor scrapers, wheel loaders, wheel tractors, graders, and dumpers (as defined in SAE J1116 (January, 1977) and J1057a (June, 1975) which are designed to operate at a maximum rated speed in excess of 20.0 km/h (12.4 mph) and which employ power (source(s) in addition to the operator control effort to effect machine steering
Off-Road Machinery Technical Comm
This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems
Air Brake Tubing and Tube Ftg Committee
The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references
Metals Technical Committee
The purpose of this SAE Standard is to specify the procedure for measuring the bank angle of motorcycles
Motorcycle Technical Steering Committee
This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed. A calculation is required to obtain the Duty Cycle operator ear
Marine Technical Steering Committee
Inclement weather can have a significant impact on surface transportation systems. It can result in hazardous conditions for travelers due to poor visibility, or wet or icy roadways. Weather applications have the potential to provide additional data to surface transportation infrastructure owners and operators, allowing them to better assess the impacts of the weather environment on or around the roadway and to better manage the surface transportation system. Such weather applications can: Collect road weather data from connected vehicles and mobile devices, increasing the number of data sources available. Provide road weather related traveler information to travelers via connected vehicles and devices, such as when and where a hazardous condition exists. Provide the ability to manage road weather response on specific roadways. This SAE Standard specifies interface requirements between vehicles and infrastructure for weather applications, including detailed systems engineering
V2X Core Technical Committee
This SAE Standard establishes specifications for mid- and side-power take-off drives that will be helpful in designing implements. Design of the implement attaching means must be tailored to each tractor, depending on attaching points available and the exact location of the auxiliary shaft
Machine Technical Steering Committee
This SAE Recommended Practice defines an architecture, including operating modes, in which an advanced driver interface system and related software exist. It also provides reference to a set of Federal Highway Administration approved guidelines for human factors characteristics of such systems and related software
Truck and Bus Electrical * Electronic Steering Committee
This SAE Standard covers the physical and performance requirements for electrodeposited copper, nickel, and chromium deposits on exterior ornamentation fabricated from die cast zinc alloys (SAE J468 alloys 903 and 925), and wrought zinc strip (ASTM B 69). This type of coating is designed to provide a high degree of corrosion resistance for automotive, truck, marine, and farm usage where a bright, decorative finish is desired
Metals Technical Committee
SAE format for a SIMPLE Strain-Life Fatigue Data Exchange File Format. The object of this SAE Standard is to provide a simple common way to exchange strain-life fatigue data collected from ASTM E 606 axial fatigue test data
Materials, Processes and Parts Council
This Recommended Practice provides a road test procedure for trucks and buses, to evaluate their compliance with Federal Motor Vehicle Safety Standard (FMVSS) 121; Air Brake Systems. Units of measure are English in lieu of metric to be consistent with FMVSS 121
Truck and Bus Brake Systems Committee
This SAE Standard specifies a method and the device for use in determining the position of the Seat Index Point (SIP) for any kind of seat
HFTC4, Operator Seating and Ride
This SAE Recommended Practice is intended for service only. Use ANSI B92.1, 1a, and B92.2M. This document contains information on inch serrated shaft ends and hole dimensions. For metric information, see TSB 003
Trans Axle Driveline Forum Committee
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of tire pressure systems, and recommended maintenance practices within the known operating environments. This document is applicable to all axle and all wheel combinations for single unit powered vehicles exceeding 7257 kg (16 000 US lb) gross vehicle weight rating (GVWR), and multi-unit vehicle combinations, up to three (3) towed units, which use an SAE J560 connector for power and/or communication, or equivalent successor connector technology, or which use a suitable capacity wireless solution. Examples of included single chassis vehicles would be – utility and delivery vans, tow trucks, rack trucks, buses, recreational vehicles, fuel trucks, trash trucks, dump trucks, cement trucks, and tractors. Examples of combination vehicles using an SAE J560 or successor connector would be – enclosed van trailers, liquid tanker
Truck and Bus Tire Committee
This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of −40 to +120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F
Hydraulic Brake Components Standards Committee
This SAE Standard may be used for all revolving cranes wherein the capacity of the crane to support loads is based on its resistance to overturning. It is not applicable to cranes wherein the capacity of the crane is based on factors other than stability
Cranes and Lifting Devices Committee
This SAE Standard covers the hardness, chemical analysis and microstructural requirements for ductile iron castings intended for high temperature service in automotive and allied industries. Commonly known as SiMo ductile iron, typical applications are in piston-engine exhaust manifolds and turbocharger parts. Castings may be specified in the as-cast or heat treated condition. For design purposes, the Appendix provides general information on the application of high temperature ductile iron castings, their processing conditions, chemical composition, mechanical properties and microstructure
Metals Technical Committee
This SAE Standard covers fittings intended for connecting service hoses, per SAE J2196, from Mobile Air-Conditioning Systems to service equipment such as manifold gauges, vacuum pumps and air conditioning charging, recovery and recycling equipment. (Figure 1
Interior Climate Control Service Committee
This standard covers tubing intended for use as high pressure fuel injection lines on a range of engines requiring tubing no larger than ¼ in (6.35 mm) OD. The material and construction of the tubing shall be cold drawn annealed low carbon seamless steel of a quality suitable for cold swaging, cold upsetting, and cold bending
Metallic Tubing Committee
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in low voltage (0 - 20 VDC) road vehicle applications. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. They are not applicable to Edge Board connector systems, > 20 VAC or DC, or to eyelet type terminals
Connector Systems Standards Committee
This document provides a method/procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use, recycled, or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum percent, must be specified using a “Z” suffix. This classification system covers thermoset High Consistency Elastomers (HCEs) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F2468
Committee on Automotive Rubber Specs
Items per page:
1 – 50 of 207244