Results
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness
This specification covers polyvinyl chloride insulated single conductor electric wires made with tin-coated copper conductors or silver-coated copper alloy conductors. The polyvinyl chloride insulation of these wires may be used alone or in combination with other insulating or protective materials
This specification defines the requirements for a grooved clamp coupling and flanges suitable for joining intermediate pressure and temperature ducting in aircraft air systems. The rigid coupling joint assembly, hereafter referred to as "the joint", shall operate within the temperature range of -65 °F to +800 °F
This specification covers a titanium alloy in the form of round bar and wire 0.625 inch (15.88 mm) and under in nominal diameter or thickness (see 8.7
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, mechanical tubing, forgings, and forging stock
This specification covers a discontinuously reinforced aluminum alloy (DRA) made by mechanical alloying 2124A aluminum powder and silicon carbide particulate (SiC). It is produced in the form of extruded bar, rod, wire, and shapes with cross section inclusive of 1-inch (25.4-mm) diameter or less (see 8.7
This specification covers an age-hardenable nitriding grade of aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light trucks having gross vehicle weight rating (GVWR) of 4540 kg (10 000 lb) or less. The test procedure is characterized by having fixed initial conditions (specified initial vehicle speed and gear selection at the starting point on the test site) to obtain vehicle interior sound measurement during road load operation over various road surfaces at specified constant speeds. The measurement data so derived is useful for vehicle engineering development and analysis
This SAE Recommended Practice is intended for use in testing and evaluating the performance of electric cooling fan (ECF) assemblies typically used for vehicle engine cooling. Conducted in a laboratory environment with intended heat exchangers, the performance measurement includes fan output in terms of airflow and pressure and fan motor input in terms of voltage and current. This information can be used to calculate the efficiency of the assembly, including aerodynamic efficiency of the fan and shroud, and electrical efficiency of the motor. The electric power consumption can be used to estimate electrical charging system sizing and fuel economy. The performance of a given fan assembly depends on the installation details of the application, including the effects of system resistance and geometries of the grill, heat exchangers, engine and other underhood components, and front end components. This document provides guidance for duplicating such details in the test setup for accurate
This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These are often called “mini coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the mini coax connection system described here is 50 Ω, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable
This specification covers a titanium alloy in the form of bars up through 1.000 inch (25.40 mm) in diameter or least distance between parallel sides, inclusive, forgings of thickness up through 1.000 inch (25.40 mm), inclusive, high-strength fastener stock up through 1.250 inch (31.75 mm), inclusive, and stock for forging of any size (see 8.7
This specification covers a discontinuously reinforced aluminum alloy (DRA) made by mechanical alloying 2124A aluminum powder and silicon carbide (SiC) particulate. It is produced in the form of extruded bar, rod, wire, and shapes with cross section inclusive of 1-inch (25.4-mm) diameter or less (see 8.7
This SAE Recommended Practice applies to motor vehicle Forward Illumination Devices which incorporate limited adaptive beam pattern capabilities. This document is to be used in conjunction with other forward lighting standards and/or recommended practices which define the base beam procedures, requirements, and guidelines
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings
This specification covers virgin, unfilled polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in dimension parallel to the direction of applied molding pressure, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm
This specification covers the requirements for electrodeposited bronze plate and its subsequent removal
This specification covers two types of virgin, unfilled polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in length, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm
This SAE Aerospace Recommended Practice (ARP) provides an overview of the various types of polytetrafluoroethylene (PTFE) backup rings for hydraulic and pneumatic fluid power applications, including their advantages and disadvantages
This standard establishes basic design criteria including preferred bend radii, straight lengths between bends, flattening and surface conditions in the bend area. Also included is a table of preferred tubing sizes and wall thicknesses and a formula for determining a minimum bend radius for a given tube diameter
The environment and test waveforms defined in this SAE Aerospace Recommended Practice (ARP) account for the best lightning data and analysis currently available. The quantified environment and levels herein represent the minimum currently required by certifying authorities, which is consistent with the approach applied in related lightning documents. Lightning, like other weather phenomenon, is probabilistic in nature. Levels and waveforms vary considerably from one flash to the next. Within this document, standardized voltage and current waveforms have been derived to represent the lightning environment external to an aircraft. These standardized waveforms are used to assess the effects of lightning on aircraft. The standardized external current waveforms have, in turn, been used to derive standardized transient voltage and current test waveforms that can be expected to appear on cable bundles and at equipment interfaces within an aircraft. When deriving these latter internal induced
This SAE Aerospace Recommended Practice (ARP) describes the etching of fluoropolymer electrical wire insulations to ensure that all facets of the process from the chemistry to the processing, to the storage and handling are well defined
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems
This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence
This standard establishes requirements for Process Control Methods to sustain product conformity. This includes training, selection of control methods, analysis and improvement of their effectiveness, and subsequent monitoring and control. It applies to all controls documented in the Control Plan. This will include but is not limited to Key Characteristics (KCs) and Critical Items (CIs). This standard aligns and collaborates with the requirements of AS9100, AS9103, AS9145, AS13000, AS13002, AS13003, and AS13004. Commercial-Off-The-Shelf (COTS) items and Standard Catalogue Items (that neither the customer nor supplier hold design authority for) are not included
The purpose of this SAE Recommended Practice is to establish reference standards for airflow measurements in the ranges required for testing automotive engine induction systems and to describe equipment that will facilitate the use of such standards to check the accuracy of various equipment and methods
This specification covers a precision cold-rolled corrosion- and heat-resistant nickel alloy in the form of sheet and strip over 0.005 to 0.015 inch (0.13 to 0.38 mm), inclusive, in nominal thickness and foil up to 0.005 inch (0.13 mm), inclusive, in nominal thickness (see 8.4
Items per page:
50
1 – 50 of 212826