Results
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
This SAE Recommended Practice establishes recommended procedures for the issuance, assignment, and structure of Identification Numbers on a uniform basis by states or provinces for use in an Assigned Identification Number (AIN).
This specification covers metric bolts and screws made from a low alloy steel of the type identified under the Unified Numbering System as UNS G87400. The following specification designations and their properties are covered: MA3376 860 MPa minimum ultimate tensile strength at room temperature MA3376-1 1000 MPa minimum ultimate tensile strength at room temperature MA3376-2 860 MPa minimum ultimate tensile strength at room temperature 516 MPa minimum ultimate shear strength at room temperature MA3376-3 1000 MPa minimum ultimate tensile strength at room temperature 600 MPa minimum ultimate shear strength at room temperature
This SAE Aerospace Recommended Practice (ARP) is written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in constructing new or adding to existing engine test cell facilities.
This SAE Standard covers 32 types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems.
This specification defines basic physical, chemical, and performance limits for 5 cSt grades of gas turbine engine lubricating oils used in aero and aero-derived marine and industrial applications, along with standard test methods and requirements for laboratories performing them. It also defines the quality control requirements to assure batch conformance and materials traceability, and the procedures to manage and communicate changes in oil formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in Appendix D Section D.2, referencing this specification. Products qualified to this specification are listed on a Qualified Products List (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before an oil is approved for use in their equipment. Approval and/or certification for use of a specific gas
The goal of the Pedestrian Test Mannequin Task Force is to develop standard specifications/requirements for pedestrian test mannequins (1 adult and 1 child) that are representative of real pedestrians to the sensors used in Pedestrian Detection systems and can be used for performance assessment of such in-vehicle systems (including warning and/or braking) in real world test scenarios/conditions. This version of the document only includes the pedestrian mannequin for vision, Lidar, and/or 76 to 78 GHz radar based Pedestrian Pre-collision systems.
Most signal and marking lighting devices have light sources (bulbs), which can be based on either filament or LED technology. To assure field replacement, it is important that light source types employed be readily available in normal service channels. This document defines the physical, electrical, and photometric characteristics necessary to achieve a proper replacement for popular types of signal and marking light sources. Some of the design characteristics in this document are listed solely for the sake of standardization and are not intended to describe the performance of lighting devices (lamp assemblies) on the vehicle. Halogen filament light sources suitable for signal and marking lighting are specified in SAE J2560.
This recommended practice is intended to provide general guidelines for the selection and proper use of cleaning and disinfecting product characteristics acceptable for use on vehicle interiors and exterior touch points (cleaning before disinfecting being best practice in general for vehicles, as with other situations), and the effectiveness of the disinfecting products with certain characteristics, as well as indicating the product characteristics that will not cause damage to those surfaces.
This SAE Recommended Practice establishes a procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers that may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853, SAE J187, SAE J272, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that review and coordination of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.
The purpose of this document is to define design, construction, operational, and maintenance requirements for hydrogen fuel storage and handling systems in on-road vehicles. Performance-based requirements for verification of design prototype and production hydrogen storage and handling systems are also defined in this document. Complementary test protocols (for use in type approval or self-certification) to qualify designs (and/or production) as meeting the specified performance requirements are described. Crashworthiness of hydrogen storage and handling systems is beyond the scope of this document. SAE J2578 includes requirements relating to crashworthiness and vehicle integration for fuel cell vehicles. It defines recommended practices related to the integration of hydrogen storage and handling systems, fuel cell system, and electrical systems into the overall Fuel Cell Vehicle.
While there are various types of Fuel Cell architectures being developed, the focus of this document is on Proton Exchange Membrane (PEM) fuel cell stacks and ancillary components for automotive propulsion applications. Within the boundaries of this document are the: Fuel Supply and Storage, Fuel Processor, Fuel Cell Stack, and Balance of Plant, as shown in Figure 1.
This document describes: a the preparatory steps to test experimental Type II, III, and IV fluids according to AMS1428; b the recommendations for the preparation of samples for endurance time testing according to ARP5485; c a short description of wind tunnel testing; d a short description of the recommended field spray test; e the protocol to generate draft holdover time guidelines from endurance time data obtained from ARP5485; f the protocol for inclusion of Type II, III, and IV fluids on the FAA and Transport Canada lists of fluids and the protocol for updating the lists of fluids; g the role of the SAE G-12 Aircraft Deicing Fluids Committee; h the role of the SAE G-12 Holdover Time Committee; and i the process for the publication of Type II, III, and IV holdover time guidelines. This document does not describe laboratory testing procedures. This document does not include the qualification requirements for AMS1424 Type I fluids (these are provided in ARP6207).
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) air and is not directly applicable to vehicles with other systems. Air over hydraulic systems are to be tested as air systems.
Items per page:
50
1 – 50 of 212784