Search
Advanced Search
of the following are true

Results

Items (208,190)
ARINC 858 Part 2 provides aviation ground system gateway considerations necessary to transition to the Internet Protocol Suite (IPS). ARINC 858 Part 2 describes the principles of operation for an IPS gateway that enables ACARS application messages to be exchanged between an IPS aircraft and a ground ACARS host. ARINC 858 Part 2 also describes the principles of operation for an IPS gateway that enables OSI-based application messages to be exchanged between an IPS host and an OSI end system. This product was developed in coordination with ICAO WG-I, RTCA SC-223, and EUROCAE WG-108
Airlines Electronic Engineering Committee
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403
Truck Bus Control and Communications Network Committee
This SAE Recommended Practice is intended to provide basic recommended practices for aid in the development and use of safe and efficient practices for all operations involving the production, handling, and dispensing of SAE J1703 motor vehicle brake fluids and SAE J1704 borate ester-based brake fluids
Brake Fluids Standards Committee
This specification defines test methods and performance criteria for ultrasonically welded wire-to-terminal bonds as shown in Figure 1. This specification subjects parts to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures referenced in this specification include thermal shock, temperature humidity cycling, and mechanical stress. This specification is intended to evaluate the strength and performance of the interface between wires and the electrical terminal pad. The graphics used are specific to the linear weld type of process equipment. Validation of the terminal is a separate task (refer to a component validation test such as SAE/USCAR-2). If the weld under test (WUT) is different than described in this section or is subjected to conditions beyond what is typical of automotive use, the test sequence may not be applicable. Ensure that parts used in other conditions are validated for the actual conditions encountered. Vehicle and product
USCAR
This document covers un-shielded balanced single twisted pair data cable intended for use in surface vehicle cables for 100 Mbps Ethernet applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission
Cable Standards Committee
This SAE Part Standard covers selected inch screws, bolts, structural bolts, and nuts manufactured in accordance with ASTM International and SAE fastener standards. Appendix A covers bolt blanks to manufacture fitted bolts of specific materials. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document
Ship Systems - Fasteners Committee
This SAE Parts Standard provides dimensional and quality assurance requirements for M6 through M36 metric sizes of studs in the following configurations in materials needed for ship system applications: a Continuous thread studs in M thread profile. b Double end studs—clamping type (also called bolt-studs) where both ends are of the same thread series but different lengths (M thread profile
Ship Systems - Fasteners Committee
This SAE Part Standard covers selected inch dimensioned set screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document
Ship Systems - Fasteners Committee
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensure that the particle retention ability of the filter is measured in a single pass, as no appreciable loading or regression will occur
Filter Test Methods Standards Committee
This SAE Recommended Practice establishes a standard method to perform screening test sequences that identify a brake friction material’s effectiveness under various test conditions. The result is an evaluation of brake friction material effectiveness under a set of defined braking conditions considered most relevant to automobile braking system development
Brake Dynamometer Standards Committee
This standard provides the guideline for enhancements to adaptive cruise control (ACC) by the addition of wireless communication from relevant vehicles (V2V) and/or the infrastructure (I2V) to augment the ACC active sensing capability. The CACC system operates under driver responsibility and supervision and is limited to the following: Does only longitudinal control of the vehicle. Uses time gap control strategy similar to ACC. Motor vehicles covered in the scope of this document include light and heavy vehicles. The message elements to realize CACC and platooning are part of the scope. The initial release covers definitions for CACC and platooning and requirements for CACC, while a subsequent release will cover the platooning requirements
V2X Vehicular Applications Technical Committee
This recommended practice establishes test procedures and best practices for PM measurements under partial flow conditions. PFDS PM testing and certification is primarily used in heavy duty applications as described in 40 CFR Part 1065 because full flow sampling systems with a dilution tunnel and CVS can be very bulky for large heavy duty engines. 40 CFR Part 1066 also allows the use of partial flow systems for light duty applications in lieu of full flow systems. PFDS does not require the use of a CVS sampling system or a full flow dilution tunnel. This makes it easier and more convenient to perform PM measurement in smaller test cells that cannot fit a large CVS or a full flow dilution tunnel. This document describes the different components/specifications of LD and HD PFDS as well as the required quality checks necessary to ensure the integrity of the sampling system. It also addresses the many sampling options and calculations that are approved by the regulations. Correlation
Emissions Standards Committee
This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document
Ship Systems - Fasteners Committee
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) b Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) Different thread forms on each end are permissible. c Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches) UNRC threads (1/4 through 4 inches) UNRC threads (1/4 through 4 inches) UNRF
Ship Systems - Fasteners Committee
This SAE Part Standard covers selected machine screw nuts manufactured in accordance with American Society for Mechanical Engineers (ASME) dimensional standards. This document covers material most often used in ship systems and equipment but its use may be applied wherever nuts of the covered materials are used. This document permits the nuts to be identified and ordered by a part identification number (PIN) as defined in this document
Ship Systems - Fasteners Committee
This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor
Truck and Bus Low Speed Communication Network Committee
This SAE Recommended Practice covers a procedure for evaluating plastic and multiple-layer coatings exposed to gravelometer testing (as defined in SAE J400) with an optical imaging and analysis system. The intent of the procedure is to detect, count and characterize instances of damage in the coated surface that fracture the top coat layer or penetrate through multiple layers of the coating system. It may be possible to extend this methodology of coating damage evaluation to specimens that have undergone test procedures or exposures that produce similar, discrete damage sites in the coating system. If so applied, evaluation results must be interpreted with respect to the limitations and intent implied by the original evaluation procedure and its associated rating system, if applicable
Textile and Flexible Plastics Committee
SAE J2886 Design Review Based on Failure Modes (DRBFM) Recommended Practice is intended for Automotive and Non-Automotive applications. It describes the basic principles and processes of DRBFM including planning, preparation, change point FMEA, design reviews, decisions based on actions completed, and feedback loops to other processes, such as design, validation and process guidelines (Appendix B - DRBFM Process Map). The intent of each fundamental step of the DRBFM methodology is presented. It is intended for use by organizations whose product development processes currently (or intend to) use Failure Mode & Effects Analysis (FMEA) or DRBFM as a tool for assessing the potential risk and reliability of system elements (product or process) or as part of their product improvement processes. DRBFM is not intended to replace FMEA however, companies interested in adopting DRBFM will benefit from the focus on specific change points and supporting engineering decisions based on detailed
Automotive Quality and Process Improvement Committee
This SAE Standard applies to refrigerant identification equipment used for identifying an acceptable level of R-1234yf purity in a refrigerant tank or vehicle MAC system labeled as containing R-1234yf, and not misidentify other refrigerants, per 5.7
Interior Climate Control Service Committee
This standard covers ultra-thin wall low voltage primary cable intended for use at a nominal system voltage of 60 VDC (60 VAC rms) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse. This standard covers SAE conductor sizes which usually differ from ISO conductor sizes
Cable Standards Committee
E-25 General Standards for Aerospace and Propulsion Systems
Areas for the standard metric series of threaded diameter-pitch combinations for aerospace internally threaded fasteners are established for the following conditions: a Area for shear stress or load in fastener thread b Area for ultimate tensile stress or load in thread
E-25 General Standards for Aerospace and Propulsion Systems
Applications include specifications, reports, ratings, texts etc., where fluid leakage rates are treated
AE-5A Aerospace Fuel, Inerting and Lubrication Sys Committee
This SAE Metric Aerospace Standard (MA) defines the requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, para-aramid reinforced, hose assembly suitable for use in 135 °C, 34,500 kPa, aircraft and missile hydraulic fluid systems
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This specification covers metric bolts and screws made from a low alloy steel of the type identified under the Unified Numbering System as UNS G87400. The following specification designations and their properties are covered: MA3376 860 MPa minimum ultimate tensile strength at room temperature MA3376-1 1000 MPa minimum ultimate tensile strength at room temperature MA3376-2 860 MPa minimum ultimate tensile strength at room temperature 516 MPa minimum ultimate shear strength at room temperature MA3376-3 1000 MPa minimum ultimate tensile strength at room temperature 600 MPa minimum ultimate shear strength at room temperature
E-25 General Standards for Aerospace and Propulsion Systems
This SAE Metric Aerospace Standard (MA) provides dimensional, performance, testing and other requirements for high strength, thin wall, double head box and combination wrenches which possess an internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the apex of the fastener’s wrenching points. This standard provides additional requirements beyond ANSI B107.9 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes
EG-1B Hand Tools Committee
This specification covers a general-purpose disinfectant in the form of a concentrated liquid
AMS J Aircraft Maintenance Chemicals and Materials Committee
E-25 General Standards for Aerospace and Propulsion Systems
This SAE Recommended Practice was developed by SAE, and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases
Fuels and Lubricants TC 3 Driveline and Chassis Lubrication
Items per page:
1 – 50 of 208190