Results
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
This specification covers a polyimide plastic in the form of isostatically molded rod, bar, and tube, unidirectionally molded plaque, and direct formed parts.
This specification provides a standard set of procedures for sampling and testing to meet the requirements of material specifications for wrought titanium and titanium alloy products, except forgings and forging stock. It is applicable to the extent specified in a material specification.
This specification covers an aluminum alloy in the form of sheet clad on both sides with a different alloy for sheet thicknesses of 0.020 to 0.128 inches (0.51 to 3.25 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, 12 inches (305 mm) and under in nominal diameter or maximum cross-sectional dimension and forging stock.
This specification covers a corrosion and heat-resistant nickel alloy in the form of round, square, and flat wire 0.625 inch (15.88 mm) and under in nominal diameter or thickness capability tested in a Spring Temper condition.
This specification covers a corrosion and heat-resistant nickel alloy in the form of seamless tubing up to and including 9.250 inches (234.95 mm) nominal OD.
This specification covers an aluminum alloy in the form of sheet and plate with thickness from 0.008 to 4.000 inches (0.20 to 101.6 mm), inclusive, clad on two sides (see 8.6).
This specification covers a closed cell silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings. Product covered by this specification is limited to a nominal 3.25 inches (82.6 mm) and under in diameter or maximum cross-sectional dimension between parallel sides (thickness) and stock of any size for forging and for flash welded rings.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers polyurethane (PUR) in the form of two-component sealing compounds.
This specification covers two types of electrically conductive, elastomeric polythioether sealing compounds that cure at room temperature. The sealing compound is supplied as either a two-component system or as premixed and frozen.
This specification covers an aluminum alloy in the form of welding wire.
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm), inclusive, in thickness, supplied in the -T361 temper (see 8.5).
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
This specification covers a low-alloy steel in the form of wire supplied as coils, spools, and straight lengths.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a special aircraft-quality, low-alloy steel in the form of bars.
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
This specification covers a titanium alloy in the form of bars and rods 1.00 inch (25.4 mm) and under in nominal diameter.
This specification covers a corrosion-resistant steel in the form of two types of aircraft tubing.
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and rolled rings 4 inches (102 mm) and under in nominal thickness, and forging stock of any size (see 8.6).
This specification covers a corrosion resistant steel in the form of wire.
This specification covers a magnesium alloy in the form of sand castings.
This specification establishes the requirements for a hard aluminum oxide coating, impregnated or codeposited with polytetrafluoroethylene (PTFE) on aluminum alloys.
This specification covers the requirements for electrodeposited tin-lead plating intended for use as a coating for corrosion protection and as a base for soldering.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, extrusions, flash welded rings up to 10 inches (254 mm) in diameter, thickness, or for hexagons, least distance between parallel sides, and stock of any size for forgings, extrusions, and rings.
This specification covers a premium aircraft-quality alloy steel in the form of bars and forgings 199 square inches (1284 cm2) and under in cross section, and forging stock of any size.
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, extrusions, flash welded rings, and stock for forging, extruding, or flash welded rings.
This specification covers a special aircraft-quality, low-alloy steel in the form of bars.
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate up to 1.000 inch (25.4 mm) in nominal thickness.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification defines limits of variation for determining acceptability of the composition of cast or wrought nickel, nickel alloy, and cobalt alloy parts and material acquired from a producer.
Items per page:
50
1 – 50 of 211952