Your Selections

Han, Jinlin
Show Only

Collections

File Formats

Content Types

Dates

Sectors

Topics

Authors

Publishers

Affiliations

Events

   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Comparative Study on the Effects of Inlet Heating, Inlet Boosting, and Double-Injection Strategy on Partially Premixed Combustion

Eindhoven University Of Technology-Jinlin Han, Shuli Wang, Bart Somers
Published 2019-04-02 by SAE International in United States
Partially premixed combustion (PPC) is a low temperature combustion (LTC) concept which can relieve soot-NOx trade-off without sacrificing efficiency. However, at low load operating range, PPC with low reactivity fuel generally undergoes long ignition delay, which gives rise to high pressure rise rate, fast heat release and even misfires. To solve these problems and maintain high efficiency simultaneously, inlet heating, inlet boosting and double-injection strategy are experimentally investigated in a heavy-duty engine. BH80 (80vol% n-butanol and 20vol% n-heptane) are blended and tested at 8 bar gIMEP in PPC mode. Inlet heating (from 40oC to 100oC), inlet boosting (from 1.4 bar to 2.5 bar) and a double-injection strategy (pilot/main injection) are attempted to reduce the maximum pressure rise rate (PRRmax). The results show that all three methods can achieve negligible soot emissions. Moreover, a correlation between global temperature at TDC and ignition delay is noticed. In other words, high global temperature after compression stroke makes BH80 easier to ignite. As a consequence, the ignition delay shortens and the maximum pressure rise rate decreases. Compared to inlet…
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Performance and Emission Studies in a Heavy-Duty Diesel Engine Fueled with an N-Butanol and N-Heptane Blend

Eindhoven University of Technology-Shuli Wang, Jinlin Han, Bart Somers
Published 2019-04-02 by SAE International in United States
N-butanol, as a biomass-based renewable fuel, has many superior fuel properties. It has a higher energy content and cetane number than its alcohol competitors, methanol and ethanol. Previous studies have proved that n-butanol has the capability to achieve lower emissions without sacrifice on thermal efficiency when blended with diesel. However, most studies on n-butanol are limited to low blending ratios, which restricts the improvement of emissions. In this paper, 80% by volume of n-butanol was blended with 20% by volume of n-heptane (namely BH80). The influences of various engine parameters (combustion phasing, EGR ratio, injection timing and intake pressure, respectively) on its combustion and emission characteristics are tested at different loads. The results showed that when BH80 uses more than 40% EGR, the emitted soot and nitrogen oxides (NOx) emissions are below the EURO VI legislation. Carbon monoxide (CO) decreases and NOx emissions increase with the increase of injection pressure. It was also found that for a constant lambda (1.55) the stable operating load range of BH80 is limited to relatively high load (>8 bar…
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Effects of Different Injection Strategies and EGR on Partially Premixed Combustion

Eindhoven University of Technology-Jinlin Han, Shuli Wang, Bart Somers
Published 2018-09-10 by SAE International in United States
Premixed Charge Compression Ignition concepts are promising to reduce NOx and soot simultaneously and keeping a high thermal efficiency. Partially premixed combustion is a single fuel variant of this new combustion concepts applying a fuel with a low cetane number to achieve the necessary long ignition delay. In this study, multiple injection strategies are studied in the partially premixed combustion approach to reach stable combustion and ultra-low NOx and soot emission at 15.5 bar gross indicated mean effective pressure. Three different injection strategies (single injection, pilot-main injection, main-post injection) are experimentally investigated on a heavy duty compression ignition engine. A fuel blend (70 vol% n-butanol and 30 vol% n-heptane) was tested. The effects of different pilot and post-injection timing, as well as Exhaust-gas Recirculation rate on different injection strategies investigated. All the measurements were performed at the same load, combustion phasing, lambda and engine speed. The results show that all three injection strategies produced ultra-low soot emission, while less NOx emission was noticed for pilot-main injection because of less diffusion combustion mode. Pilot-main injection strategy…
This content contains downloadable datasets
Annotation ability available